Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Angular contact
15TAC47C
15TAC47C is a angular contact designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 15 × 47 × 15 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Does YJB’s 15TAC47C table specify your preload or locknut torque?
The examined website and downloadable PDF leave two fields labelled only by units: “(kN) 2.6” and “(N.mm) 50”. They do not name the quantities. Do not turn either into an installation instruction for a ball-screw support; request their definitions and the specification of the offered bearing set.
Unit labels do not identify what must be adjusted.
Return the two fields to YJB and ask for their quantity definitions, measurement conditions and whether they describe an individual bearing, a specified matched arrangement or a particular test. Keep them unassigned until answered. In particular, this source does not establish that 50 N·mm is a screw-support locknut tightening requirement.
The same row shows 12000 beneath the grease-lubrication heading without a unit in the examined header. The directory historically records it as a speed field; this guide does not treat that interpretation as a newly verified continuous-duty limit. Obtain its unit and the selected construction's applicable speed condition.
A 15 mm-wide item does not define the assembled screw support.
The confirmed nominal dimensions are d = 15 mm, D = 47 mm and B = 15 mm, with approximate mass 0.13 kg. The manufacturer-provided series diagrams [3] show a 60° section and both individual and paired mounting illustrations. They do not identify the count, direction or preload of your quoted set.
For an existing support, preserve the old complete marking, number of bearings, orientation and spacer arrangement. Ask whether the offer is an individual replacement or a matched set, and obtain the set drawing and mounting basis. A quote for two bare 15TAC47C items does not itself establish factory matching.
Two nominal 15 mm widths add to 30 mm by arithmetic. That is not a complete stack dimension: spacer dimensions, tolerances, locating faces and the selected preload arrangement still belong to the controlled assembly drawing. Do not design the locknut position from the arithmetic alone.
The illustrated shoulder symbols have to be resolved on the selected drawing with actual bounds. Neither a series picture nor the 15/47/15 envelope supplies the required shaft/housing fits or corner limits.
The 11.5 kN field and load ratings answer different catalogue questions.
YJB labels 11.5 kN as maximum axial load and shows 27 in the Cor rating column. Its Cr field reads “21.527”, but the same series table contains strings such as “28.541.5” in other Cr cells. This makes the intended numeric format a question for the manufacturer. Preserve the raw field, request its confirmed value and do not split it into a guessed 21.5 or use it as a verified rating in a calculation.
Do not use the maximum-axial entry as an unspecified continuous working-force allowance or reinterpret the unnamed 2.6 kN entry as an approved preload. Supply the screw's force cases in each direction, reversals and actual support arrangement, then request the selected set's load and preload assessment with the manufacturer's definitions.
If the goal is positioning accuracy, state the assembly's required test condition and result. The catalogue has no verified stiffness, positioning result or lifetime for your machine. The next usable deliverable is a defined bearing set and support drawing with resolved field meanings, rather than a quote that simply repeats the three load numbers.
21.527 The source displays 21.527 under Cr. Other TAC rows contain malformed-looking numeric strings; confirm the intended value rather than splitting or using this field in a calculation.
27
12000 The source labels this column grease lubrication but gives no unit. Historical rpm interpretation awaits confirmation.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
16 mm
Mean diameter dm
(D + d) / 2
31 mm
Arithmetic on the figures above — not a bearing life calculation for your load case.
YJB publishes precision angular-contact, double-row cylindrical roller and ball-screw bearing ranges. Its NN3006-K-W33 catalogue separates bearing dimensions from mounting callouts. Confirm the offered bore, precision and lubrication configuration against the actual spindle drawing.
Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.
Fields absent from the recorded dataset.
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Other designations with the same 15x47x15 mm envelope.
Actually read full row and header in DataTables/32 and exact detail: dimensions, mass, displayed ratings and axial entry. Unit-only fields and grease-column unit ambiguity retained; no inferred installation limits.
Downloaded one-page manufacturer PDF, text and rendered page examined. Repeats 2.6 and 50 with units only; does not establish preload or locknut torque.
Three manufacturer-provided images actually viewed: 60-degree series section, individual/paired mounting illustration and product picture. Not a controlled assembly drawing or proof of a supplied matched set.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies