The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22210
22210 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 50 × 90 × 23 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
What should receiving inspection verify when a Luan 22210 offer changes the suffix or mass?
The archived table gives 22210, 22210K and 22210W33 equal dimension and rating entries, but different reference masses. That is a reason to obtain the exact construction and document revision, not a basis for accepting a substitute or diagnosing a counterfeit from weight. Keep the order, package and bearing marking tied to one agreed specification.
The mass column differs although the other displayed entries match.
Luan’s retained original table [1] lists these three exact rows beneath a page titled 22218CCW33. The table row, rather than the page title, identifies each item.
Recorded designation
d / D / B, unit unstated
Grease / oil, r/min
Dynamic / static, kN
Reference mass, kg
22210
50 / 90 / 23
3800 / 4800
52.2 / 73.2
0.87
22210K
50 / 90 / 23
3800 / 4800
52.2 / 73.2
0.87
22210W33
50 / 90 / 23
3800 / 4800
52.2 / 73.2
0.62
The reference-mass difference between the plain row and W33 row is 0.25 kg, calculated as 0.87 minus 0.62. The examined table gives no explanation or mass tolerance. It does not establish whether the difference reflects construction, a document error or another basis. Do not silently change either entry, assign it to a cage material, or turn 0.87 kg into a pass/fail limit.
The dimension heading does not state a unit; these figures are shown exactly as the catalogue prints them until the maker confirms the unit. Equal numbers also do not establish equal bore geometry, internal design or interchangeability. Ask Luan for the current revision and drawings of the exact proposed part. If the supplier quotes 22210K or 22210W33 against an order for 22210, request a separately identified substitution assessment and the buyer’s approval before delivery.
Define the receiving record before the shipment arrives.
The following is a proposed purchasing record, not a report of a tested shipment. Agree its scope with Luan and the buyer’s quality team:
Identity: match the order’s complete maker and designation to the package label, bearing marking and supplier delivery document. Record any difference without dropping suffixes to make the names agree.
Traceability: retain the supplier’s lot identification and its relationship to the delivery or inspection documents. A catalogue webpage does not authenticate a particular lot.
Specification: use the supplier-approved drawing with dimension units, tolerances, bore form and agreed clearance. The three raw entries above cannot supply those acceptance limits.
Mass, when specified: agree whether a check covers the bare bearing or packaged item, the measurement method and the applicable reference and tolerance. A gross package weight cannot be compared directly with an unexplained catalogue reference mass.
Discrepancy: record photographs, markings, measured fields and the document revision; hold the affected item for the agreed disposition instead of installing it because the nominal numbers match.
No sample mass or measurement appears in this review. An item that weighs differently is not automatically proven counterfeit, and one that matches 0.87 kg is not automatically proven genuine. Resolve a discrepancy through the maker’s construction and traceability evidence rather than a weight-only conclusion.
Inspection should not create a contamination or preservative problem.
SKF’s mounting guidance [2] explains retaining original packaging until mounting and checking associated components for cleanliness and prescribed tolerances. It also treats preservative compatibility and grease-filled sealed or shielded bearings differently. This is general preparation guidance, not proof of how Luan’s plain 22210 is delivered.
Ask Luan what protection, preservative or lubricant is actually supplied and which handling procedure applies. Arrange any required unwrapping and measurement in the buyer’s controlled inspection area. Do not wash a received bearing simply to obtain a “clean” mass reading or infer a cleaning solvent from this catalogue. Preserve the labels and photographs needed to resolve identity while protecting the bearing’s condition.
Receiving approval and mounting readiness are separate decisions. A matching delivery still needs the shaft, housing and mounting procedure checked against the approved drawing. The published 52.2/73.2 kN and 3800/4800 r/min entries do not constitute a machine acceptance test or combined-duty approval.
The maker’s original HTML was retained from an earlier capture and reopened for this review. A fresh source navigation on 2026-10-09 failed with a certificate-name error. These archival readings therefore do not confirm current production, stock or a revised specification.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22210.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Exact three rows and headings read and visually checked in retained original HTML. Dimensions have no stated unit; r/min, KN and Kg explicit. Reference masses 0.87/0.87/0.62 have no explanation or acceptance tolerance. Fresh navigation on 2026-10-09 failed with a certificate-name error.
PDF index201 newly read, rendered and actually viewed. Preparation principles only; no SKF cleaning method, tool code, delivered condition or acceptance limits transferred to Luan.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies