BearingIndex
THE BEARINGINDEX DIRECTORY

22210K — 50 × 90 × 23 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22210K

22210K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 50 × 90 × 23 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
50 unit unconfirmed
Outside D
90 unit unconfirmed
Width B
23 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

The “50” entry for Luan 22210K is not enough to select a mounting-table row.

A mounting table needs an identified bearing, a confirmed dimension and unit, the applicable taper and a defined measurement method. The archived Luan row does not supply all of these. Resolve the offered construction first, then retain the maker’s starting condition and mounting acceptance criteria together.

Four inputs are missing from a mounting instruction built only from this row.

The exact archived 22210K row [1] lists d/D/B as 50/90/23, grease/oil speed ratings as 3800/4800 r/min, basic dynamic/static ratings as 52.2/73.2 kN and reference mass as 0.87 kg. Its dimension heading does not state a unit. It gives no taper ratio, accessory number, mounting starting condition or drive-up criterion.

Before accepting a supplier’s installation sheet, ask for these connected inputs:

Controlled dimension and unit
Which drawing and revision defines the delivered bore? The bare “50” entry must not automatically become a verified 50 mm mounting input.
Bore and mating seat
Which bore form and taper are offered, and does the procedure cover the direct seat or the identified sleeve and shaft arrangement?
Method and starting condition
Does the instruction use measured clearance reduction, axial movement or another maker-approved method? How is its starting point established?
Applicable limits
Which bearing construction, shaft condition and measurement interval does the table actually cover, and which result must be recorded?

K remains part of the exact recorded name. The plain 22210 row has the same displayed numbers and reference mass, but the archive names it separately. Neither equal numbers nor a supplier removing K from a quote establishes that the two delivered bore arrangements are equivalent.

Table headings and footnotes are part of the mounting data.

SKF’s spherical-roller mounting table [2] illustrates the issue: its bore intervals use separate “greater than” and “less than or equal to” headings, and its axial movement columns distinguish two taper ratios. An exact boundary belongs to the interval that includes it; choosing the next row by rounding or overlooking the inequality changes the instruction.

That SKF table also states that its listed axial drive-up values are not valid for the SKF Drive-up Method and describes assumptions about solid steel shafts and general applications. A method’s name therefore cannot be treated as interchangeable with another method’s axial-distance column. These are examples of how to read the source, not a selected SKF row or setting for Luan 22210K.

Obtain Luan’s applicable procedure for the confirmed offered part and mating components. Keep its method, initial reading or starting position, prescribed criterion and final recorded result on the same installation record. No nut angle, torque, axial travel, clearance reduction, taper ratio or sleeve designation is supplied here.

SKF further distinguishes securing the inner ring from obtaining the correct operating radial clearance: housing fit and ring temperature differences also matter. Ask Luan to address those conditions in the proposed clearance selection. A mounting movement alone is not evidence that the running clearance is correct.

Use the equipment’s approved installation procedure and the maker’s applicable criteria. This review has no actual machine measurements or completed mounting test. The retained original Luan HTML was re-read and its exact row viewed; a fresh source navigation on 2026-10-09 failed with a certificate-name error. No new controlled drawing or current stock is established.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22210K
52.273.2380048000.872026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22210K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22210K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22210K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22210K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22210K row ↗

    Exact 22210K and adjacent plain/W33 rows read and visually checked in original saved HTML. Dimension unit absent; speed/load/mass units explicit. No taper ratio or mounting limits. Fresh navigation failed certificate-name error on 2026-10-09.

  2. SKF · spherical-roller mounting table and method notes, printed page 789 ↗

    PDF index790 re-read and actually viewed. Interval inequalities, taper columns, method exclusions and shaft assumptions explain evidence requirements. No SKF numerical setting or selected table row assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.