BearingIndex
THE BEARINGINDEX DIRECTORY

22211 — 55 × 100 × 25 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22211

22211 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 55 × 100 × 25 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
55 unit unconfirmed
Outside D
100 unit unconfirmed
Width B
25 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Does the 87.2 kN static entry answer the load case you actually need to check?

The static rating in Luan’s retained 22211 row is greater than its dynamic rating, but that does not give two interchangeable working-load limits. A buyer needs the actual bearing reactions, the critical operating states and the applicable rating method. Average running load can conceal a peak that needs a separate static assessment.

60 kN dynamic and 87.2 kN static describe different rating questions.

The exact Luan 22211 row [1] gives basic dynamic rating 60 kN and static rating 87.2 kN, grease/oil speed entries 3400/4300 r/min and reference mass 0.86 kg. Its d/D/B entries are 55/100/25, with no stated dimension unit. These are retained catalogue fields, not a measured machine duty or a confirmed current drawing.

SKF’s static-load guidance [2] explains that the basic static rating relates to a defined contact-stress and permanent-deformation basis. It is not a promise that an equipment assembly can carry that external load without any relevant consequence. The dynamic rating instead belongs to a running-life assessment; neither can be used as the total machine payload.

Do not select the larger 87.2 figure as the allowable load simply because it is labelled static. Submit the radial and axial reactions at this bearing position, derived from the actual arrangement and loads. The distribution among supports, overhung forces or moments may matter where present. No support layout or reaction calculation has been supplied here, so a payload conversion or pass/fail result would be invented.

Collect the load states that the real application has.

SKF’s guidance identifies stationary high loads, slow oscillation and temporary peaks during rotation as situations needing static-load verification. These are conditional checks for the buyer; this page does not claim Luan 22211 is installed in a particular machine or experiences any of them.

State, if presentInformation to give the assessorSeparate question
Normal rotationActual speed and radial/axial reaction history, lubrication and required life.What dynamic-life assessment applies to the complete offered bearing?
Stationary holding or slow oscillationPeak reactions, duration or motion pattern and required positional/running behaviour.What static-load criterion and deformation consequence must be checked?
A transient peakThe credible event and simultaneous radial/axial reactions, with their calculation or measurement basis.Does the critical peak require a separate static check alongside the running-life calculation?

Preserve the simultaneous radial/axial combination for each state. Combining the largest radial entry from one unrelated state with an axial entry from another may not describe a real event; averaging a brief peak into a life calculation can also miss the static question. Have the responsible designer identify the governing combinations and their basis.

Ask for model-specific factors and criteria instead of inventing an allowable load.

SKF explains that a combined load is assessed through an equivalent static bearing load, using factors appropriate to the bearing type, and that the maximum relevant load combination must be considered. Its general equation does not provide Luan 22211’s actual factors or an agreed safety criterion.

Ask Luan or the responsible bearing assessor to identify the applicable equivalent-load method, required factors and criterion for the offered construction. Keep the input reactions and source documents with the resulting assessment. A bare comparison of external force with 87.2 kN does not establish a static safety margin.

For a rotating application, obtain the separate running-life result with its load/speed history, lubrication assumptions and required life. A satisfactory static assessment does not establish fatigue life, and a running-life calculation alone need not resolve a temporary peak. No life value, static factor, deformation acceptance limit or allowable payload is calculated here.

The maker’s retained original table was reopened, its exact 22211 row and headings read and actually viewed. Fresh source navigation on 2026-10-09 failed with a certificate-name error. The archive does not establish a current production revision, offered clearance, material grade or machine approval. SKF’s technical explanation supplies background only; its numerical contact stresses, deformation figures and selection thresholds are not prescribed for this Luan item.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22211
6087.2340043000.862026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22211.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22211

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22211.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22211 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22211 table row ↗

    Exact row/header read and visually checked in retained HTML: 60/87.2 kN, 3400/4300 r/min and 0.86 kg; dimension unit absent for 55/100/25. Fresh navigation failed with a certificate-name error on 2026-10-09.

  2. SKF · static rating and load-state verification, printed pages 104–105 ↗

    PDF index 105 newly read, rendered and actually viewed; index 106 equivalent-static-load text re-read. Static-rating meaning and governing combined load used as background. No SKF coefficients, numerical acceptance criteria or working payload assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.