BearingIndex
THE BEARINGINDEX DIRECTORY

22211K — 55 × 100 × 25 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22211K

22211K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 55 × 100 × 25 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
55 unit unconfirmed
Outside D
100 unit unconfirmed
Width B
25 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Which clearance condition does the supplier’s 22211K figure describe?

A supplied clearance range, a cold mounted reading and a running-clearance assessment describe different conditions. Luan’s retained 22211K row publishes ratings and speed entries but no delivered clearance class or mounting criterion. Keep those conditions distinct when reviewing the quotation and installation record.

Ask whether a clearance figure is supplied, mounted or operating.

The exact retained Luan 22211K row [1] gives dimension entries 55/100/25 without a dimension unit, grease/oil speeds 3400/4300 r/min, basic dynamic/static ratings 60/87.2 kN and reference mass 0.86 kg. It does not provide a clearance class, range, taper ratio, fitted clearance or operating-clearance result. K in the name does not fill those missing fields.

Supplied condition

Identify the complete offered bearing and the maker’s initial radial-clearance class and range, including the measurement basis. Do not assume that a bare 22211K quote includes C3 or another class.

Cold mounted condition

Record the approved mounting method and the specified measurements before and after mounting, with the relevant assembly and measurement conditions. A change caused by mounting is not the same field as the supplied range.

Operating condition

Obtain the assessment for the assembled bearing under the actual fit and thermal conditions. The operating requirement is not established by one cold reading.

Have Luan use these condition names on the proposal and applicable procedure. A reply containing only “clearance within range” cannot be evaluated until it identifies which condition, range and complete part it means.

The inner-ring mounting change is only one part of the clearance assessment.

SKF’s clearance-selection explanation [2] separates interference-fit effects from temperature differences between the bearing rings and surrounding components. Its fit discussion includes inner-ring expansion and outer-ring compression. Therefore an enquiry that describes only the shaft or sleeve can omit a housing influence that the assessor needs.

Send the actual mating-component drawings, fits, materials and relevant wall or shaft geometry to the responsible assessor. SKF’s illustrated reduction factors state assumptions about a solid steel shaft and a thick-walled cast-iron or steel housing. Those assumptions cannot automatically be assigned to an unknown 22211K assembly. No fit-reduction factor or clearance calculation is supplied here.

The same guidance explains that start-up can produce a ring-temperature difference greater than the steady-state difference. Where that condition is relevant, describe both states; a housing surface temperature or a final stable reading does not by itself identify both ring temperatures. This page has no measured temperatures and does not invent a cold-start event for your machine.

A larger clearance suffix is not an automatic solution.

SKF’s selection explanation checks both the required minimum and whether the resulting maximum clearance is acceptable. That is why selecting a larger class solely to avoid an assumed loss of clearance can leave another unresolved operating requirement. It is not a recommendation to order this Luan item as C3, C4 or any other class.

Ask Luan to identify the agreed initial range, mounting criterion and required operating condition for the exact construction. Retain the supporting fit and thermal assumptions with that decision. If the shaft, sleeve, housing, lubricant system or operating sequence changes, submit the change for review rather than reusing a reading from a different assembly.

No micrometre range, fit designation, drive-up distance, torque or temperature limit is inferred from the 55/100/25 entries. Their unit must first be confirmed on the offered drawing. Neither the 3400/4300 r/min entries nor the 60/87.2 kN ratings prove that a particular assembled clearance is acceptable.

The original Luan HTML was retained from an earlier capture and reopened; its exact row and headings were actually viewed. Fresh source navigation on 2026-10-09 failed with a certificate-name error. No current controlled clearance specification, mounting measurement or operating test has been obtained. SKF supplies general explanation only; its coefficients, class values and numerical settings are not assigned to Luan.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22211K
6087.2340043000.862026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22211K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22211K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22211K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22211K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22211K row ↗

    Exact row and unit headings read and visually checked in retained original HTML. No dimension unit, delivered clearance class/range or mounting result. Fresh navigation failed with a certificate-name error on 2026-10-09.

  2. SKF · fits, thermal differences and clearance range, printed pages 184–185 ↗

    PDF indices 185–186 re-read, rendered and actually viewed. Fit and thermal influences, start-up/steady-state distinction and minimum/maximum range checks used as background. No numerical coefficients or clearance settings transferred to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.