The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22211W33
22211W33 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 55 × 100 × 25 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
Does the lubrication proposal address both solid contamination and water exposure?
Luan’s archived 22211W33 row does not specify a seal system, filtration requirement or water-ingress test. Its W33 name and catalogue ratings cannot prove that the proposed housing and lubricant arrangement control contamination. Describe the real environment and check the limits of any life calculation used in the proposal.
The exact catalogue row contains no contamination qualification.
Luan’s retained 22211W33 row [1] gives 55/100/25 under a dimension heading without units, grease/oil speeds 3400/4300 r/min, dynamic/static ratings 60/87.2 kN and reference mass 0.84 kg. It does not state a filter specification, housing seal, water limit or environmental test result.
The neighbouring plain and K rows have the same displayed ratings and speeds, with reference mass 0.86 kg. The W33 mass difference does not demonstrate additional sealing or a cleaner lubricant supply. Missing seal data equally does not prove that the delivered installation has no seals; the complete offer and housing arrangement must answer that question.
Describe the environment that actually applies: for example, dust or process particles, water contact or washdown, and the possible routes through the seals, supply oil or handling process, where present. These are questions for the buyer, not claims that this model has been tested in a dusty or wet machine. Have the maker confirm the offered bearing features and the equipment designer confirm the surrounding control arrangement.
A solid-particle factor cannot stand in for a water assessment.
SKF’s contamination-factor table [2] explicitly limits its scale to typical solid contaminants; its footnote excludes water and other fluids detrimental to bearing life. A calculation using that factor alone therefore does not demonstrate that a water-exposed arrangement has been assessed.
Issue, if relevant
Evidence to request
Keep the interpretation separate
Solid particles
Lubricant cleanliness and sampling basis, likely particle sources, sealing and filtration or grease-handling controls.
Any selected cleanliness factor needs its stated method and actual evidence; catalogue ratings do not supply it.
Water or another fluid
Actual exposure and ingress route, lubricant compatibility and a separately agreed assessment and test or monitoring basis.
A solid-particle factor does not automatically include these effects.
An unspecified “clean” system
Identify what was sampled, where and when, and which acceptance method and criterion are used.
A filter label or a visually clear lubricant is not a complete contamination assessment.
No SKF contamination factor is selected here, and no filter micron rating, water concentration limit or resulting life value is assigned to Luan 22211W33. The actual application, lubricant and control design have not been provided. Keep the limits of a calculation visible instead of treating a single cleanliness number as a general environmental approval.
Tie the control proposal to an agreed lubricant-check record.
Ask the responsible parties to identify how contamination is prevented or removed and how the condition will be checked. For an oil system, the proposal may need filtration and any relevant water-management provision; for a grease arrangement, handling, replenishment and the specified seals or purge route need review. Which features apply must come from the actual assembly, not from W33 alone.
Agree the lubricant sampling location and method, the conditions recorded with the sample, the responsible assessor and the applicable action criteria. A sample from one convenient location should not silently become proof of the lubricant condition at every bearing position. Keep the record connected to the complete part, housing and service procedure.
If an assessment assumes a certain cleanliness or absence of water, ask how the proposed system maintains and verifies that assumption during operation. A catalogue rating or a clean new sample does not establish that future condition. This page reports no contamination test, field sample or service-life result.
The original Luan source HTML was retained from an earlier capture, reopened and its exact row and headings actually viewed. Fresh source navigation on 2026-10-09 failed with a certificate-name error. The archived table does not establish current stock or an environmental qualification. SKF’s footnote explains a calculation boundary; it does not certify Luan’s construction or prescribe this installation’s lubricant limits.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22211W33.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Original saved row and headings read and actually viewed. Dimension unit absent; no sealing, filtration, water limit or environmental test in the examined row. Fresh navigation failed with a certificate-name error on 2026-10-09.
PDF index 106 re-read, rendered and actually viewed, including the footnote excluding water/other detrimental fluids from the solid-contaminant scale. No numerical factor, life prediction or lubricant limit transferred to Luan.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies