The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22212K
22212K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 60 × 110 × 28 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
An accessory ending in “312” is not enough to specify the mounting set for Luan 22212K.
The retained Luan row identifies 22212K but gives no accessory pairing or assembly drawing. NSK’s catalogue shows adapter and withdrawal arrangements as separate entries for its own 22212EAKE4. Use the distinction to ask for the right complete mounting set; do not transfer that pairing to Luan from a shared number.
The sleeve table names the bearing it applies to.
The exact retained Luan 22212K row [1] lists 60/110/28 with no stated dimension unit, grease/oil speed entries 3200/4000 r/min, dynamic/static ratings 81.8/112 kN and reference mass 1.22 kg. It provides no sleeve designation, shaft-interface diameter, taper ratio or complete mounting set.
These are separately labelled length fields on different drawings, not two interchangeable lengths to choose by convenience. The named accessories and the 55 mm shaft interfaces are NSK catalogue facts for its complete paired bearing. They do not establish Luan 22212K’s sleeve, shaft size or required axial space.
The distinction between nominal bearing bore d and shaft diameter d₁ also shows why a bare bearing-bore entry cannot automatically be treated as the machine shaft diameter. Luan’s unit must first be confirmed on its controlled drawing, and its actual mating arrangement must be identified. No shaft size is selected for Luan here.
Request the assembly and removal route, not only a sleeve number.
Start with the existing machine drawing and complete bearing, sleeve and locking-component markings where available. Ask Luan to identify whether the proposed part uses a direct tapered seat, an adapter arrangement or a withdrawal arrangement, and to provide the applicable controlled section. An enquiry containing only “22212K with 312 sleeve” leaves the bearing pairing and assembly route unresolved.
Have the supplier list every item included in the quote and identify the shaft interface, locating or retention components, required assembly space and applicable mounting procedure. Give the equipment designer the proposed section so the bearing’s axial position and the surrounding parts can be checked. Do not calculate the assembly space by subtracting the different NSK length fields above.
Also identify the planned removal route and the access needed for the approved tools or procedure. The mounting and maintenance arrangement must be reviewed together. No heating temperature, tool selection, nut torque, axial movement or clearance-reduction criterion is supplied by the examined Luan row.
NSK’s adapter-table remark explains X as an adapter-sleeve slit feature linked to its washer-tab requirement. It is a reason to retain the complete accessory name and matched locking parts; it is not a general instruction to use an NSK washer on a Luan assembly. Have Luan confirm its own matched set and the procedure for the actual parts.
The original Luan HTML was retained from an earlier capture and its exact row/header reopened and actually viewed. Fresh navigation on 2026-10-09 failed with a certificate-name error. NSK’s original catalogue table pages were read, rendered and visually checked for the specific pairings. Neither publication supplies a confirmed Luan accessory offer, actual installation measurement or stock status.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22212K.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Exact row/header read and actually viewed in saved original HTML. Dimension unit absent and no accessory pairing, taper ratio or shaft interface supplied. Fresh navigation failed with a certificate-name error on 2026-10-09.
PDF index 174 read, rendered and actually viewed: exact 22212EAKE4 + H312X, d/d₁ and B₁ headings, and adapter X remark. NSK pairing only; no Luan accessory approval inferred.
PDF index 178 read, rendered and actually viewed: exact 22212EAKE4 + AHX312, d/d₁ and B₃ headings. Distinct arrangement, not an interchangeable length or inferred Luan shaft size.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies