The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22212W33
22212W33 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 60 × 110 × 28 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
Does a different maker’s lubrication code preserve the requirements behind Luan 22212W33?
An alternative can use a different suffix vocabulary. NSK’s own catalogue identifies oil-groove/hole features for specific 22212 entries, while Luan’s retained row is named 22212W33. Compare the actual features and complete parts rather than adding, removing or translating suffixes by appearance.
The feature statement must remain attached to the named catalogue entry.
Luan’s exact retained 22212W33 row [1] gives dimension entries 60/110/28 without a stated unit, grease/oil speeds 3200/4000 r/min, dynamic/static ratings 81.8/112 kN and reference mass 1.2 kg. The examined row does not include a groove or hole drawing. Its designation is a starting point for the maker’s construction confirmation.
NSK’s original spherical-roller table [2] separately lists 22212EAE4 in the cylindrical-bore column and 22212EAKE4 in the tapered-bore column. Both have an asterisk. The table’s remark states that asterisked entries are NSKHPS bearings supplied with an oil groove and holes. Its K note specifies the taper for NSK’s listed tapered entries.
That is actual evidence about those NSK catalogue entries. It does not define the geometry or delivery condition of Luan’s W33 bearing. It also does not establish a universal E4-to-W33 interchange rule. A different maker may document a lubrication feature without using the same suffix text, while the other construction fields remain important.
The cylindrical and tapered NSK entries are separately identified despite sharing displayed boundary dimensions and the oil-feature remark. Matching a lubrication feature is therefore only one part of an alternative review; it does not settle the bore arrangement. Do not borrow NSK’s taper note or accessory pairings for Luan.
Keep a proposed alternative on a separate specification line.
If a supplier proposes another make against a 22212W33 requirement, ask for its full part number and controlled drawing. Compare these requirements explicitly:
Requirement
Evidence for each complete candidate
What a suffix alone cannot settle
Lubricant feed interface
Maker-confirmed groove/hole geometry and coordinated housing-feed drawing.
Whether the actual housing delivers lubricant through the offered feature.
Bore and mounting route
Confirmed cylindrical or tapered construction and actual direct-seat or sleeve arrangement.
A common numeric prefix or common oil feature does not select the same mounting set.
Clearance and internal construction
Complete designation, drawing and agreed initial-clearance range for each make.
No class or cage is established by translating one lubrication code.
Duty and rating basis
Each maker’s load and speed definitions assessed for the actual lubricant system and duty.
A feature match does not transfer load factors or approve operation.
Preserve the original requirement and put the proposed substitute alongside it. Do not produce a combined designation assembled from one maker’s base code and another maker’s suffix, or delete W33 from the original order simply because a proposal looks similar. Have the responsible assessor record which requirements the substitute satisfies and which differences need approval.
Luan’s dimension unit remains unresolved until its controlled drawing is obtained; NSK’s mm-labelled table cannot confirm that unit for Luan. No complete replacement, delivered specimen or housing-feed test has been approved here. No NSK rating, taper, groove dimension, hole count or mounting instruction is transferred to this Luan record.
The original Luan HTML was retained from an earlier capture, reopened and its exact row/header actually viewed. Fresh source navigation on 2026-10-09 failed with a certificate-name error. NSK’s exact catalogue row, asterisks, column labels and explanatory remark were read, rendered and visually checked. These publications supply evidence for a comparison, not current stock or permission to substitute.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22212W33.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Exact row/header in saved original HTML read and actually viewed. Dimension unit absent; no groove/hole drawing. Fresh navigation failed with a certificate-name error on 2026-10-09.
PDF index 134 read, rendered and actually viewed: starred 22212EAE4/22212EAKE4, separate bore columns and oil-groove/hole remark. NSK-specific evidence; no code equivalence, Luan taper or replacement approval inferred.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies