BearingIndex
THE BEARINGINDEX DIRECTORY

22213K — 65 × 120 × 31 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22213K

22213K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 65 × 120 × 31 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
65 unit unconfirmed
Outside D
120 unit unconfirmed
Width B
31 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Where was the 22213K bore measured? Agree the reference before comparing a reading.

The retained Luan 22213K row records 65/120/31 but does not state dimension units, a bore section or a measurement reference. A tapered-bore candidate needs more than a single diameter reading. Confirm the offered drawing and where its bore dimension applies before calling a delivered part correct or incorrect.

A catalogue bore entry is tied to a drawing convention.

The exact Luan 22213K row [1] gives 65/120/31 with no stated dimension unit, grease/oil speeds 2800/3600 r/min, dynamic/static ratings 88.5/128 kN and reference mass 1.63 kg. Those entries do not describe a bore measurement procedure.

NTN’s 2203/E catalogue [2], printed B-220, separately lists 22213EAKD1 under tapered bore with 65/120/31 mm, and its note defines K as a 1:12 taper. The table also has a cylindrical-bore entry, 22213EAD1. NTN’s column labels distinguish the constructions even where the three nominal dimensions match.

An older NTN catalogue [3], printed 108, gives an explicit measurement convention: its tapered-bore d dimension is referenced to the end with the smaller bore. Its complete tapered designation on that page is 22213EKD1. This older nomenclature is retained as a cited example; it is not the current offered NTN specification or a Luan drawing.

QuestionDocumented NTN exampleNeeded for Luan 22213K
Which complete part?22213EAKD1 in 2203/E; 22213EKD1 in the older catalogueFull offered designation and controlled revision
What unit?mm in the 2203/E boundary tableMaker confirmation; original row is unstated
What taper?1:12 in the 2203/E K noteOffered bore section and stated taper ratio
Where does d apply?Smaller-bore end in the older catalogue noteExplicit reference plane on Luan’s approved drawing

These NTN definitions cannot establish Luan’s taper, reference plane or tolerance. A reading taken at an unspecified axial location cannot be compared reliably with an unqualified catalogue number. Do not assume a larger-end reading should equal the smaller-end nominal value, or calculate an acceptance diameter from 31 and a borrowed taper ratio.

Record the measurement context before deciding the disposition.

For an offer presented as tapered bore, attach the approved Luan drawing to the order and agree the inspection basis before delivery. The report should make the following information recoverable:

  • Part and orientation: complete designation, batch identification, drawing revision and which face is the smaller-bore end.
  • Measured feature: diameter or taper being checked, reference plane, axial location and measurement directions. A photo of one reading without these details does not define the feature.
  • Method and conditions: maker-agreed instrument or gauge method, relevant calibration record, part condition and measurement temperature. A convenient receiving tool is not automatically adequate for taper or bore-form assessment.
  • Criteria and result: approved dimensions/tolerances and method-specific acceptance criteria, recorded observations, reviewer and any required clarification. This page supplies no tolerance class or gauge setting.

If the measured feature or reference is unclear, preserve the part and evidence and obtain clarification against that drawing before making a pass/fail decision. A successful nominal bore check would still not confirm mounting clearance, sleeve compatibility or suitability for the machine’s load and thermal duty. Those require their own assessment.

The archived Luan plain 22213 and 22213K rows have the same three numerical entries and listed load/speed/mass values. That equality does not establish the same bore construction or receiving procedure. The K must remain part of the enquiry and proposed drawing identity.

The exact Luan row/header was reopened and actually viewed in saved original HTML; fresh access on 2026-10-09 failed with a certificate-name error. Both NTN PDF pages were read, rendered and actually viewed. No delivered sample was measured, and no Luan inspection procedure has been approved here.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22213K
88.5128280036001.632026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22213K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22213K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22213K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22213K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22213K row ↗

    Exact retained row and headers read and actually viewed: unstated dimension unit, no bore section/reference or receiving procedure. Archive recheck; fresh certificate-name failure on 2026-10-09.

  2. NTN · 2203/E, exact 22213 entries and K note ↗

    PDF page 209, printed B-220/B-221, read, rendered and actually viewed: 22213EAD1/22213EAKD1 columns, mm boundary dimensions and 1:12 K note. NTN-specific, not Luan construction or interchange approval.

  3. NTN · older catalogue, tapered-bore reference convention ↗

    PDF page 109, printed page 108, read, rendered and actually viewed. Older 22213EKD1 row and smaller-bore-end d note used only as historical measurement-reference example; no current specification, drawing-label assumption or Luan tolerance inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.