The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22214K
22214K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 70 × 125 × 31 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
A shaft diameter tolerance alone does not complete the 22214K mounting specification.
Luan’s archived 22214K row does not identify a sleeve, shaft drawing or fit criteria. A maker’s fit table can distinguish sleeve-mounted tapered bores from cylindrical bores and can add shaft-form requirements. Preserve those qualifications when preparing the actual mounting drawing.
Use the fit table for the interface actually being assembled.
The exact Luan 22214K row [1] records 70/125/31 without a dimension unit, 2600/3400 r/min grease/oil entries, 95/142 kN dynamic/static ratings and 1.66 kg reference mass. It provides no shaft tolerance, sleeve pairing or mounting section.
NTN’s 2203/E catalogue [2], printed B-220, lists a separately named 22214EAKD1 tapered-bore entry with 70/125/31 mm. Its B-213 shaft table separates cylindrical-bore bearing fits from tapered-bore bearings using adapter or withdrawal sleeves. A diameter group in the cylindrical-bore portion is not a sleeve-mounted shaft recommendation.
The tapered-bore sleeve row gives h9/IT5, with a note allowing h10/IT7 for power-transmitting shafts in the stated NTN context. Its footnote specifically includes shaft roundness and cylindricity requirements. The table also states that its values and fits concern solid steel shafts. These qualifications belong with the table entry.
Proposal detail
Why it needs its own confirmation for Luan 22214K
Nominal diameter and unit
The source’s 70 is not a confirmed shaft diameter or even a confirmed dimension unit. Obtain the offered drawing and actual mounting interface.
Diameter tolerance
Identify the approved shaft feature and tolerance; do not select a cylindrical-bore table row for a sleeve arrangement.
Shaft form
Specify and inspect the maker-approved roundness/cylindricity requirements as well as diameter. A size reading does not document both.
Material and construction
Identify the actual shaft material and solid/hollow section. NTN’s solid-steel-table qualification does not approve other constructions.
No h9, IT5, h10 or IT7 requirement has been assigned to Luan here. NTN’s separate complete part, dimensions and table cannot supply Luan’s missing unit, sleeve compatibility or application approval.
Make the shaft, accessory and inspection responsibilities explicit.
First obtain the Luan bore drawing and choose the actual mounting route with the responsible designer and maker. If a sleeve is proposed, name its complete designation and locking components, and identify which surfaces establish the assembly position. If another route is proposed, obtain the criteria for that route instead of reusing a sleeve table.
Then issue a drawing package that identifies the controlled shaft features, their size and form requirements, locating/retention arrangement and relevant measurement references. Request a receiving report against those features. A diameter-only report cannot show that a separately specified form criterion was checked; a report that omits the applicable revision cannot identify the approved basis.
Keep shaft geometry verification separate from the bearing’s mounting-clearance and retention checks. An accessory fitting onto the shaft does not establish the bearing’s final clearance or secure retention. Obtain the delivered construction’s mounting procedure, initial and final clearance criteria where applicable, and locking verification. This page supplies no tightening torque, drive-up distance or clearance-reduction setting.
The archived plain 22214 and 22214K entries share their listed numbers. That does not make their bore or fit procedures identical. The complete K designation and its offered drawing must survive from enquiry through order and inspection.
Luan’s exact saved row/header was read and actually viewed; fresh access on 2026-10-09 failed with a certificate-name error. NTN’s exact row and shaft-table qualifications were read, rendered and actually viewed. No Luan sleeve compatibility, shaft fit or inspection procedure has been approved, and no actual shaft has been measured in this review.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22214K.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Exact saved row/header read and actually viewed; unit unstated, no shaft/accessory drawing or fit criteria. Fresh certificate-name failure on 2026-10-09; archive recheck only.
PDF pages 209 and 205, printed B-220/B-221 and B-212/B-213, read, rendered and actually viewed. Exact 22214EAKD1 entry, sleeve/cylindrical interface distinction, form footnote and solid-steel scope. NTN guidance is not a Luan fit or accessory approval.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies