BearingIndex
THE BEARINGINDEX DIRECTORY

22215 — 75 × 130 × 31 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22215

22215 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 75 × 130 × 31 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
75 unit unconfirmed
Outside D
130 unit unconfirmed
Width B
31 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Luan’s 22215 row does not publish a load-rating increase over its 22214 row.

The original table gives both designations 95 kN dynamic and 142 kN static ratings. Their dimension entries, speeds and masses differ. If 22215 is proposed as an upgrade, ask which benefit is actually supported and what changes the machine requires; the model number alone supplies neither a life improvement nor a replacement approval.

The adjacent plain-designation entries show different changes.

The following values come from the exact retained Luan 22214 and 22215 rows [1], not a cross-maker comparison or measured samples.

Published fieldLuan 22214Luan 22215
d / D / B entries70 / 125 / 31; unit unstated75 / 130 / 31; unit unstated
Dynamic load rating95 kN95 kN
Static load rating142 kN142 kN
Grease / oil speed entries2600 / 3400 r/min2400 / 3200 r/min
Reference mass1.66 kg1.75 kg

The examined publication gives no increase in either load-rating field for 22215, and its two speed entries are lower. These observations do not explain the internal design or prove that both delivered products behave identically. They show why an “upgrade” claim needs more than the higher designation or mass.

The recorded envelope entries differ and their unit is absent. Obtain both current drawings and units before any interface redesign. Do not assume the existing shaft and housing accept 22215, or turn this comparison into a same-dimension replacement suggestion. No mounting equivalence or current revision has been confirmed.

A life target needs load, speed and operating conditions, not only C.

If the purpose of the proposal is longer fatigue life, request the calculation basis and assumptions for the actual machine. SKF’s general rating-life explanation [2], printed pages 88–89, distinguishes the dynamic rating C from equivalent dynamic load P and includes speed when expressing basic life in hours. Its service-life discussion also addresses lubrication, contamination, mounting and environmental conditions.

The shared 95 kN entry is only one input. It does not establish P for either installed bearing, the applicable load cycle, or the lubrication and mounting state. SKF’s own modification factors are not Luan factors and are not assigned here. No life in hours or improvement percentage can be established from these two rows alone.

SKF defines L10 as a statistical fatigue-life basis for a population under defined conditions. It is not a promise that every individual bearing lasts that long, nor an assessment of every possible failure cause. A proposed life figure should state the basis, units, reliability and operating assumptions rather than appearing as an unconditional service guarantee.

Ask the proposer to separate the decisions:

  1. What benefit is claimed? Identify fatigue life, a different mounting interface or another specific requirement. Do not substitute a heavier catalogue mass for evidence of that benefit.
  2. What changes? Identify the current and proposed complete constructions, controlled drawings, interfaces and operating case. Assess mechanical changes separately from the claimed performance benefit.
  3. What supports it? Obtain maker-specific ratings and calculation inputs, the responsible application assessment and any agreed validation. Keep analytical predictions, observed results and commercial guarantees distinct.

Luan’s exact rows and headers were read and actually viewed in original saved HTML; fresh access on 2026-10-09 failed with a certificate-name error. SKF’s explanatory pages were read, rendered and actually viewed. No Luan life calculation, measured redesign trial or guaranteed improvement has been obtained.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22215
95142240032001.752026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22215.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22215

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22215.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22215 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22215 and 22214 rows ↗

    Both original saved rows and headers read and actually viewed: same 95/142 kN ratings, different raw dimensions, speed pairs and masses. Dimension unit unstated. Fresh certificate-name failure on 2026-10-09; archive recheck only.

  2. SKF · Rolling bearings, rating-life meaning and inputs ↗

    PDF pages 90–91, printed 88–89, read, rendered and actually viewed. General statistical life definition and load/speed/service-condition context; no SKF factors, Luan life estimate, replacement assessment or test result transferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.