BearingIndex
THE BEARINGINDEX DIRECTORY

22216 — 80 × 140 × 33 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22216

22216 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 80 × 140 × 33 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
80 unit unconfirmed
Outside D
140 unit unconfirmed
Width B
33 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Luan’s 115 kN rating is not a published axial-load allowance for 22216.

The retained row supplies dynamic and static ratings but no equivalent-load factors or vertical-shaft assessment. Before selecting this bearing for combined loads, establish the actual bearing reactions and obtain the offered construction’s calculation basis. Another maker’s e and Y values cannot fill the missing Luan fields.

Start with loads at this bearing, not the equipment’s headline load.

The exact Luan 22216 row [1] publishes 115 kN dynamic and 180 kN static ratings, 2200/3000 r/min grease/oil entries and 2.2 kg reference mass. Its 80/140/33 dimension entries lack a unit. The row contains no e, Y1, Y2 or Y0 factors and no allowable axial load.

For a combined-load proposal, ask the responsible designer to identify the radial and axial reactions at this particular bearing for the stated arrangement and duty stages. An equipment weight or transmitted load is not automatically the reaction at each bearing. Keep the calculation tied to the actual bearing positions and locating arrangement, shaft orientation and operating cycle.

Then request Luan’s equivalent-load method and factors for the complete offered construction. Keep the dynamic-life assessment and static assessment separate. Neither subtracting an axial load from 115 kN nor treating 180 kN as an axial allowance follows from this published row.

The separate NTN 22216EAD1 entry illustrates the missing calculation fields.

NTN’s 2203/E catalogue [2], printed B-220/B-221, lists its 22216EAD1 with e = 0.22, Y1 = 3.14, Y2 = 4.67 and Y0 = 3.07. The same spread identifies the dynamic equivalent radial load using different X/Y choices according to the axial-to-radial load ratio, and gives a separate static equivalent radial load expression. These are coefficients for that NTN entry.

What the NTN spread distinguishesWhat the Luan proposal must establish
Dynamic equivalent load: X/Y selection depends on Fa/Fr relative to eUse the offered maker’s method, actual bearing reactions and applicable coefficients. A dynamic rating alone omits these inputs.
Static equivalent load uses its own axial factor Y0Obtain the actual static assessment basis and relevant load cases; do not reuse a dynamic result as a complete static check.
Coefficients are listed alongside a complete bearing designationRetain manufacturer and full construction when documenting factors. The shared numerical stem does not approve a cross-maker factor transfer.

The quoted 0.22 and Y values are not Luan values and are not used to calculate a Luan load, life or safety margin here. NTN’s confirmed millimetre dimensions also cannot confirm the unit of Luan’s source. A completed assessment needs Luan-specific data and actual machine inputs, not a hybrid of the two catalogues.

Add a specific review when the shaft is vertical or axial load is large.

NTN’s general spherical-roller explanation, printed B-211 [2], warns that with vertical shafts or large axial loads, the roller row not carrying the axial load can become lightly loaded and skidding may cause wear. It asks users to consult NTN Engineering when Fa/Fr exceeds the catalogue factor e. That request is an engineering-review condition, not a universal maximum axial load or a Luan approval threshold.

If that operating situation applies to the proposed 22216 installation, send the maker the actual orientation, radial/axial load cases and speed cycle. Ask how both rows remain appropriately loaded and what operating restrictions or alternative arrangement the assessment requires. Keep the response with the exact bearing and machine revision. Merely remaining below a basic rating does not answer the lightly loaded-row concern.

The exact Luan archive row/header and NTN’s coefficient spread and orientation discussion were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error. No machine reactions, Luan coefficients, skidding diagnosis or application approval have been established by this review.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22216
115180220030002.22026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22216.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22216

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22216.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22216 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22216 row ↗

    Original saved exact row/header read and actually viewed; raw dimensions have no unit, e/Y factors and axial-load assessment absent. Fresh certificate-name failure on 2026-10-09; archive recheck only.

  2. NTN · 2203/E, 22216EAD1 coefficients and spherical-roller orientation context ↗

    PDF pages 209 and 204, printed B-220/B-221 and B-211, read, rendered and actually viewed. Exact NTN e/Y factors and dynamic/static distinction; vertical/high-axial-load skidding discussion. No NTN factors, Luan axial allowance or machine approval transferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.