The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22217
22217 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 85 × 150 × 36 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
“Self-aligning” does not supply a permissible angle for the offered Luan 22217.
Luan’s row records ratings and speed entries but no misalignment allowance. To assess a shaft-deflection or housing-alignment proposal, describe the angle and how its direction behaves relative to the outer ring. General catalogue guidance does not approve the actual arrangement.
Specify the relative ring alignment and its behaviour during operation.
The exact retained Luan 22217 row [1] records 85/150/36 without a dimension unit, 2000/2800 r/min grease/oil entries, 145/228 kN dynamic/static ratings and 2.8 kg reference mass. It publishes no angular misalignment value or qualification for a shaft-deflection case.
For an alignment proposal, distinguish a measured installation condition from a predicted condition under load or temperature. Identify the inner and outer ring axes, which components rotate, and whether the direction of misalignment remains fixed relative to the outer ring. An angle on one assembly drawing does not describe every operating state.
Alignment information
Decision it enables
Magnitude, unit and defined ring axes
State what the measurement or calculation represents. An unspecified “shaft angle” cannot be compared with a ring-misalignment allowance.
Direction relative to the outer ring
Identify whether that direction is constant or changes during operation; do not treat rotating deflection as a static installation offset.
Load and thermal state
Keep each angle with the operating state that produced it, rather than quoting an unloaded check as the loaded result.
Surrounding arrangement
Show the actual abutments, housing and sealing arrangement when requesting the maker’s assessment.
A permissible-angle table comes with operating and arrangement conditions.
SKF’s general spherical-roller guidance [2], printed 780–781, qualifies its angle table for light to normal load and a constant misalignment position relative to the outer ring. It also says that the arrangement and abutments affect whether the guideline values can be used fully. Those qualifications are part of the guidance, not optional footnotes.
For a changing position relative to the outer ring, SKF discusses additional sliding and a much more restricted misalignment range. Its examples include rotating shaft deflection in vibrating screens and certain paper-machine rolls. This does not diagnose the proposed Luan installation or assign it a numerical limit.
Do not take an angle from another maker’s table and enter it as a Luan 22217 acceptance tolerance. Request Luan’s allowance for the complete offered construction and the described operating case, including clearance and any surrounding limitations. Keep the response with the relevant drawing and calculation revision. A successful unloaded rotation check does not demonstrate the loaded alignment case.
If no part-specific allowance or operating alignment basis is available, record the assessment as unresolved. The catalogue’s spherical-roller classification cannot replace those missing inputs, and this page supplies no calculated permissible angle or blanket vibration approval.
The Luan original saved row/header and SKF’s table with its facing-page qualifications were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error. No actual machine angle, shaft deflection or Luan application approval has been verified.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22217.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Original saved row/header read and actually viewed; dimension unit and permissible misalignment absent. Fresh certificate-name failure on 2026-10-09; archive recheck only.
PDF pages 782–783, printed 780–781, read, rendered and actually viewed. Table 6 read with its constant/changing alignment, load and arrangement qualifications. No SKF angular limit assigned to Luan 22217.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies