The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22217K
22217K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 85 × 150 × 36 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
Luan Rolling Bearing prints 145 kN dynamic and 228 kN static for 22217K. NSK prints 310 kN and 325 kN for its 22217EAKE4 of the same 85 × 150 × 36 mm size. Same boundary dimensions, different internal design: size the bearing on the rating of the maker who will actually supply it.
Luan’s dynamic rating is less than half of NSK’s, and its static rating about 70 %. Neither source explains the difference, and this page does not guess at one. What it means for a buyer: a life calculation done with NSK’s 310 kN does not hold for a Luan bearing, and the reverse. Ask Luan for the rating of the exact offered designation and recalculate with it.
Luan prints its loads in KN but gives no unit for d, D and B. NSK prints the same 85 / 150 / 36 in millimetres. Ask Luan to confirm the unit on its drawing before machining to it.
K means a tapered bore. The sleeve is a separate order line.
NSK defines the K suffix as a tapered bore, with a 1:12 taper (K30 is 1:30). For 22217EAKE4 it names the H317X adapter sleeve and the AHX317 withdrawal sleeve as associated products. [3] Luan’s table gives no taper ratio and names no sleeve, so do not assume a Luan accessory number from NSK’s.
Mounted on an adapter sleeve
Send the shaft diameter, the old sleeve, nut and lock-washer markings, and ask the supplier to quote the matched set. The shaft interface is then the sleeve bore, not the bearing’s 85 mm.
Mounted directly on a tapered seat
Send the shaft-seat drawing and ask the supplier to confirm the taper and its tolerance for the offered bearing.
Either way, a tapered-bore bearing is mounted by driving it up the taper until the internal clearance falls to a set value. SKF’s installation guide [2] explains the method. Get Luan’s starting clearance and the residual clearance or drive-up to reach for its bearing; this page does not supply one.
For housing and shaft shoulders, NSK gives da 95–101 mm, Da 135–140 mm and ra max 2 mm for its bearing. [3] Luan publishes none; ask for its drawing.
Luan Rolling Bearing, Lu’an, Anhui.
六安滚动轴承有限公司 (Luan Rolling Bearing Co., Ltd., brand LZ) says it was set up in 2003 as a restructuring of the former Lu’an Bearing Factory, founded in 1970, and that it makes spherical and cylindrical roller bearings. Its contact page gives the address as the intersection of Shanyuan Road and Chunhui Road, Jin’an Economic Development Zone, Lu’an, Anhui 237161, and the phones 0564-3698200 (office) and 0564-3698228 (sales). [4][5]
The company page says it passed quality, environmental and occupational-health system certification in May 2016. No certificate number, issuer or expiry date was readable: the certificate images did not load. Ask for the current certificates with the quotation.
The 22217 rows appear in the series table on Luan’s 22218CCW33 product page; there is no page for 22217K alone. The table lists no 22217CC or CA variant. Its 22217, 22217K and 22217W33 rows share the size and ratings, so the suffix you order has to come from the old bearing’s marking and the mounting, not from the table.
The https address of Luan’s site still shows a certificate-name error. The table was read over plain http; no certificate check was bypassed.
What each manufacturer published.
Manufacturer
Dynamic load rating (kN)
Static load rating (kN)
Limiting speed — grease (rpm)
Limiting speed — oil (rpm)
Reference mass (kg)
Source recorded
Luan Rolling Bearing 22217K Luan prints d, D and B without a unit; loads are in KN.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Rows 22217, 22217K, 22217W33: 85/150/36 (no unit on d D B), grease 2000 / oil 2800 r/min, Dynamic 145 KN, Static 228 KN, 2.8 / 2.8 / 2.7 kg. No taper, sleeve or mounting data. Read over http 2026-10-30; https still fails the certificate-name check.
Established 2003 from the former Lu’an Bearing Factory (1970), brand LZ, registered capital 38 million yuan, May 2016 three-system certification statement. Certificate images not readable. Read 2026-10-30.
Address in Jin’an Economic Development Zone, Lu’an 237161; office and sales phone numbers. Read 2026-10-30.
Guide checked 2026-10-30. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies