BearingIndex
THE BEARINGINDEX DIRECTORY

22218 — 90 × 160 × 40 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22218

22218 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 90 × 160 × 40 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
90 unit unconfirmed
Outside D
160 unit unconfirmed
Width B
40 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 22218 replacement needs seating geometry, not just three matching dimensions.

The retained Luan row gives principal dimensions but no abutment diameters or corner limits. A separate LYC 22218/W33 page publishes those additional interfaces explicitly. Use that distinction to request the offered bearing’s own drawing before approving an existing shaft or housing.

Principal dimensions and abutment dimensions answer different questions.

The original saved Luan 22218 row [1] records 90/160/40 without a dimension unit, grease/oil entries of 1900/2600 r/min, dynamic/static ratings of 168/272 kN and 4 kg reference mass. It does not give shaft or housing abutment dimensions, bearing chamfers or permissible corner radii.

For a separate, fully identified part, LYC’s live 22218/W33 page [2] states d/D/B as 90/160/40 mm, then adds an abutment diagram and the following fields. They belong to that LYC part, not to the offered Luan 22218.

LYC 22218/W33 fieldPublished valueInterface identified by its diagram
da min101 mmMinimum shaft-side abutment diameter; separate from bearing bore d.
Da max149 mmMaximum housing-side abutment diameter; separate from bearing outside diameter D.
ra max2 mmAbutment corner-radius limit shown on the mounting diagram.

The same LYC page separately lists bearing r min as 2 mm. Keep the bearing chamfer field and mounting-corner field distinct even where their displayed numbers coincide. None of these LYC dimensions supplies Luan’s missing limits or confirms that the two constructions interchange.

Check where the ring actually seats against the shoulder.

NTN’s general shaft-and-housing guidance [3], printed A-148, explains the purpose: the shoulder must contact the flat part of the ring end face, while its corner must avoid interfering with seating. It also discusses spacers where a larger shaft fillet is required or an abutment gives insufficient contact. These are design questions, not permission to machine an arbitrary radius.

For the proposed Luan 22218 replacement, put the existing machine drawing alongside the offered bearing’s controlled drawing. Identify the shaft shoulder and housing shoulder separately; include their diameters, actual corner or relief geometry, and the end face each supports. If an existing drawing contains only a nominal bearing seat, the interface review remains incomplete.

Ask the responsible maker or machine designer to resolve any conflict between the shoulder corner and bearing chamfer, and to assess the supporting face for the axial load case. If a spacer is proposed, obtain its controlled geometry and acceptance in this particular arrangement before changing the stack. Do not treat a spacer as a universal repair or derive its thickness from the missing Luan data.

NTN’s Table 14.3 has a “special use” column whose footnote expressly excludes spherical roller bearings. Selecting that smaller abutment height simply because the expected axial load is light would discard a material qualification. Its general table is not a part-specific Luan 22218 drawing; this page supplies no numerical Luan shoulder-height approval.

Record the outcome by interface and drawing revision: confirmed seating/contact, required drawing change, or unresolved maker limit. A match of d, D and B alone cannot close those decisions. No actual shoulder measurements, spacer design or installed seating result has been verified here.

The exact Luan archived row/header, LYC’s live dimensions and original abutment diagram, and NTN’s guidance with its footnotes were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error; its saved table was rechecked rather than presented as a new fetch.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22218
1682721900260042026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22218.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22218

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22218.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22218 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22218 row ↗

    Exact archived row/header read and actually viewed; principal-dimension unit and mounting/chamfer limits absent. Fresh certificate-name failure on 2026-10-09; archive recheck only.

  2. LYC · live 22218/W33 dimensions and abutment diagram ↗

    Exact complete-part page read and dimension fields actually viewed on 2026-10-09; original mounting diagram opened and viewed separately. Millimetre units and mounting values belong to this LYC part only.

  3. NTN · Rolling Bearings, shaft and housing fitting dimensions ↗

    PDF page 78, printed A-148/A-149, text read, rendered and actually viewed. Sections14.2.1–14.2.2, Figure14.1 and Table14.3 footnotes reviewed; no numerical mounting limit transferred to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.