The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22218K
22218K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 90 × 160 × 40 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
“90 bore” does not identify the shaft for a sleeve-mounted 22218K proposal.
NSK lists both an adapter and a withdrawal sleeve for its complete 22218EAKE4C4, but their shaft-diameter fields differ. A quotation for Luan 22218K needs the actual mounting arrangement and its own approved accessory pairing before the shaft interface can be assessed.
Two associated sleeves share nominal bore d but not shaft diameter d1.
The exact saved Luan 22218K row [1] gives 90/160/40 without dimension units, 1900/2600 r/min grease/oil entries, 168/272 kN dynamic/static ratings and 4 kg reference mass. It names no sleeve and gives no sleeve-mounted shaft dimension.
As a separate documented example, NSK’s complete 22218EAKE4C4 page [2] identifies a tapered bore and lists H318X and AHX318 as associated products. Opening their own official pages shows why the bearing’s nominal bore is not enough to specify the shaft:
NSK accessory
Nominal bore d
Shaft diameter d1
H318X · adapter [3]
90 mm
80 mm
AHX318 · withdrawal sleeve [4]
90 mm
85 mm
These are NSK’s explicit field definitions and accessory associations. They do not approve either sleeve for Luan 22218K or authorize an 80 or 85 mm Luan shaft. A proposed sleeve code must be supported by the offered maker’s pairing and assembled drawing, rather than copied from this example.
The NSK part also explicitly states C4 radial internal clearance. A truncated quotation reading only “22218K” loses that property. Retain each proposal’s full identity and maker-defined properties; NSK’s C4 statement does not establish Luan’s clearance.
Have the seller identify the assembly that will sit on the existing shaft.
Start with the actual machine arrangement. Identify whether the bearing is on a direct tapered seat, an adapter, or a withdrawal sleeve. Send the shaft drawing with its dimension definitions and the existing accessory markings. Then ask for a controlled assembled drawing for the proposed Luan part. The answer should connect the bearing, sleeve, shaft and retention arrangement, not merely repeat the bearing envelope.
Keep width fields tied to their components and assembly state. NSK’s H318X page lists B1 as accessory width, whereas its AHX318 page labels B4 as the sleeve-and-bearing width before the sleeve is driven into the bore. The latter is not an installed axial position. Neither can be substituted for Luan’s recorded bearing width B or used to infer mounting travel.
Request the proposed assembly’s axial envelope and installed reference from the responsible maker, together with the mounting and retention instructions for that exact combination. If the available drawing identifies only the bearing, the shaft interface and accessory package remain unresolved. Do not order or machine the shaft on the assumption that every sleeve arrangement uses the bearing’s nominal bore as its shaft diameter.
When comparing offers, mark each difference explicitly: complete bearing identity, mounting route, maker-approved sleeve, defined shaft interface and assembled axial references. An accessory substitution is a change to that proposal and needs its own documented review. This page supplies no Luan sleeve compatibility, taper dimensions, drive-up distance or locknut torque.
The exact Luan archived row/header and NSK’s live complete-part, H318X and AHX318 fields were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error. No actual machine drawing, Luan accessory pairing or installed assembly has been verified.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22218K.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Current complete-part page read; exact identity and tapered-bore/C4 properties actually viewed, associated H318X/AHX318 pages followed. Separate NSK example, not Luan approval.
Live accessory page read and shaft/nominal-bore and pre-installation B4 definitions actually viewed on 2026-10-09. No installed Luan dimension derived.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies