BearingIndex
THE BEARINGINDEX DIRECTORY

22219 — 95 × 170 × 43 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22219

22219 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 95 × 170 × 43 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
95 unit unconfirmed
Outside D
170 unit unconfirmed
Width B
43 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A lightly loaded 22219 needs more than a favourable load-rating comparison.

A large catalogue rating does not answer whether an unloaded or lightly loaded machine can operate satisfactorily. Luan’s 22219 row publishes neither a minimum-load requirement nor a reference-speed field. Keep those missing inputs visible when reviewing startup and empty-running duty.

The load ratings in this row do not define a minimum operating load.

The exact archived Luan 22219 row [1] records 95/170/43 without dimension units, 1800/2400 r/min grease/oil entries, 212/322 kN dynamic/static ratings and 4.2 kg reference mass. It contains no minimum-load formula, reference-speed field or empty-running qualification.

SKF’s general minimum-load explanation [2], printed 106, discusses skidding, smearing and cage damage in very light-load situations, and says that more accurate requirements are in the product sections. It highlights rapid acceleration and repeated starts/stops as conditions deserving attention. This is background, not a diagnosis of a Luan bearing or the actual machine.

The same SKF catalogue’s spherical-roller section, printed 784, distinguishes an overall minimum-load expression from oil-lubricated cases that depend on speed ratio n/nr. It defines nr as reference speed. Thus, a general rule for roller bearings cannot be copied without retaining the particular product and lubrication basis.

Do not enter Luan’s oil entry of 2400 r/min as nr merely because both are speed numbers, or combine Luan’s static rating with another maker’s minimum-load method. No Luan minimum load is calculated here. Obtain the responsible maker’s method, definitions and applicability for the complete offered construction.

Give the maker the lowest-load operating states, not only the highest load.

For a proposal that includes empty running, distinguish the machine’s process load from the reaction carried by each bearing. Identify the load basis for each state; an empty process does not, by itself, establish a zero bearing reaction. Keep speed and acceleration with that same state rather than attaching a maximum load from a different part of the cycle.

Operating state to describeInformation needed for the assessment
Starting or acceleratingBearing reaction during the acceleration, speed change and duration; identify whether load arrives before or after acceleration.
Empty or lightly loaded steady runningReaction at each bearing, speed and time at that state, with the actual lubrication arrangement.
Normal loaded runningIts own reaction and speed, so it is not mistaken for the unloaded state.
Stopping and repeated cyclingLoad/speed sequence and frequency of starts and stops, retaining any unresolved transient reaction.

Ask Luan to assess those cases for the exact 22219 offered. If the maker’s required inputs or minimum-load guidance are missing, record the light-load review as unresolved. A load-rating margin at full production and a short unloaded rotation check cannot replace that assessment.

Any proposed change to bearing size, lubrication, operating sequence or preload needs the responsible designer’s review of the complete arrangement. Do not apply an improvised preload just to reach a borrowed catalogue threshold. This page recommends no numerical preload, alternate bearing or run-in procedure, and verifies no skidding or damage in the actual equipment.

The original saved Luan row/header and SKF’s general and spherical-roller minimum-load pages were read, rendered where applicable and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error. No machine load history, maker minimum-load response or operating test has been obtained.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22219
212322180024004.22026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22219.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22219

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22219.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22219 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22219 row ↗

    Exact saved row/header read and actually viewed; dimension units, minimum-load requirement and reference-speed field absent. Fresh certificate-name failure on 2026-10-09; archive recheck only.

  2. SKF · Rolling bearings, requisite minimum load and spherical-roller load guidance ↗

    PDF pages 108 and 786, printed 106 and 784, text read/rendered/actually viewed. General vs product-specific guidance and oil-case reference-speed definition retained; no SKF formula or threshold applied to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.