BearingIndex
THE BEARINGINDEX DIRECTORY

22219K — 95 × 170 × 43 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22219K

22219K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 95 × 170 × 43 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
95 unit unconfirmed
Outside D
170 unit unconfirmed
Width B
43 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 22219K mounting proposal must show where thermal movement is accommodated.

Securing a bearing on its shaft does not describe the function of both supports. Before changing a sleeve, housing or end cover, identify the locating support and the designed movement path. The Luan catalogue row supplies neither that arrangement nor an axial-travel allowance.

Axial movement within a bearing differs from movement of a ring on its seat.

The exact retained Luan 22219K row [1] lists 95/170/43 without dimension units, 1800/2400 r/min grease/oil entries, 212/322 kN dynamic/static ratings and 4.2 kg reference mass. It does not identify an axial locating function, housing fit, end-cover arrangement or available movement.

SKF’s arrangement guidance [2], printed 70–71, separates the locating support, which positions the shaft axially, from the non-locating support, which accommodates relative thermal movement and component tolerances.

It distinguishes two movement mechanisms. Certain bearing designs accommodate displacement internally; for spherical roller bearings it describes a non-locating arrangement using a loose fit between a ring and its seat. SKF also notes that a ring moving on its seat can introduce axial loads. Its Figure 11, printed 75, illustrates a spherical-roller pair with different locating functions.

This general arrangement example is not an installation drawing for Luan 22219K. Do not assume that its self-aligning classification or K suffix supplies internal axial float, or that tightening a sleeve determines how the whole shaft accommodates thermal movement.

Review both supports before changing the housing or retention parts.

Ask the responsible designer to mark the axial locating support and the intended moving interface on the complete machine section. Identify the ring faces restrained by shoulders, covers or other retention parts. A proposal showing only the bearing and sleeve cannot establish whether the original support function survives the replacement.

Question on the assembly drawingEvidence needed to close it
What locates the shaft axially?The identified support and its retention/load path, including relevant faces and components.
Where can relative axial movement occur?The specified bearing or ring/seat interface; identify which component moves relative to which.
Can the movement occur through the required range?Required cold/hot displacement and tolerances compared with the actual designed clearance and surrounding geometry.
Does the change preserve the arrangement?Review changed sleeve, seat, cover or retention geometry against the original support functions and axial load case.

If a cover, shoulder or other component restricts the designed moving interface, have the designer resolve that conflict before assembly approval. Do not remove a retaining component or loosen a fit as an improvised remedy. The appropriate fit and retention depend on the complete application, and ring movement is not necessarily free of axial force.

Keep any movement estimate with its assumptions: shaft and housing states, geometry, material data and tolerances. No thermal-expansion coefficient, working temperature or allowable travel is published for this Luan row, and none is invented here. A cold assembly check cannot by itself establish movement at the intended hot state.

Record which interfaces have been approved and what remains unresolved. No actual shaft displacement, ring sliding, housing clearance or axial reaction has been measured on this page. The assessment must come from the responsible maker/designer for the offered construction and machine.

The exact Luan archived row/header and SKF’s locating/non-locating explanation and Figure 11 were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error; the original saved row was rechecked.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22219K
212322180024004.22026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22219K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22219K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22219K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22219K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22219K row ↗

    Exact archived row/header read and actually viewed; dimension unit and assembly axial-movement/retention data absent. Fresh certificate-name failure on 2026-10-09; archive recheck only.

  2. SKF · Rolling bearings, locating/non-locating arrangements ↗

    PDF pages 72–73 and 76–77, printed 70–71 and 74–75, read; explanation and Figure 11 rendered and actually viewed. Internal displacement distinguished from ring/seat movement; no fit or travel approval transferred to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.