BearingIndex
THE BEARINGINDEX DIRECTORY

22220K — 100 × 180 × 46 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22220K

22220K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 100 × 180 × 46 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
100 unit unconfirmed
Outside D
180 unit unconfirmed
Width B
46 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 22220K mounting instruction needs the method, its starting reference and its own acceptance basis.

A copied drive-up value is incomplete without the applicable method and conditions. The Luan row has no approved mounting procedure. A separate SKF 22220EK example shows why an exact diameter boundary and a table footnote must survive the quotation.

“Greater than 100 mm” and “up to 100 mm” are different conditions.

The retained exact Luan 22220K row [1] gives 100/180/46 without a dimension unit, 1700/2000 r/min grease/oil entries, 222/358 kN dynamic/static ratings and 5 kg reference mass. It contains no drive-up distance, locknut angle or mounting-method approval.

In a separate SKF catalogue example [2], printed 796, the complete 22220EK has d=100 mm. Its mounting guidance, printed 788, recommends the SKF Drive-up Method for d>100 mm. That wording does not include exactly 100 mm; equally, it does not say that the method is prohibited at 100 mm.

Table 7, printed 789, uses lower-bound > and upper-bound ≤ symbols. Its 80<d≤100 mm interval includes 100 mm. Keep those symbols with the table instead of turning the next “100–120” line into an inclusive range. This illustrates reading the SKF source correctly; it is not authorization to apply that table to Luan’s unit-unconfirmed row.

The named SKF Drive-up Method also cannot be equated with merely reading an axial-drive-up column. Table 7’s axial-drive-up column has a footnote expressly excluding that method. Choose the approved procedure before choosing an input or acceptance value; do not combine pieces from different procedures.

The mounting criterion and operating clearance remain separate checks.

The same SKF table qualifies its axial-drive-up and locknut-angle guideline columns for solid steel shafts and general applications, notes difficulty establishing an exact starting position, and says drive-up differs between bearing series. Its side note also separates preventing ring creep from ensuring correct radial clearance in operation: housing fit and ring-temperature differences still matter.

For the actual Luan proposal, ask the maker to identify the complete mounting method and its controlled procedure. The response must define the starting reference, what is measured, the criterion used to accept the installation and which construction/shaft arrangement it covers. A number sent without that basis cannot close the mounting review.

Required part of the instructionWhat must stay with it
Applicable procedureExact offered bearing, taper, shaft or sleeve, approved method and document revision.
Initial referenceMaker-defined start condition and measurement reference; do not substitute an arbitrary first-contact position.
Mounting acceptanceThe prescribed measurement and criterion, with the actual recorded result for that assembly.
Clearance in operationSeparate review of the intended running clearance, housing fit and temperature conditions.

No SKF drive-up amount, tightening angle or clearance-reduction value is supplied as a Luan instruction. Confirm Luan’s dimension units first, then obtain the construction-specific procedure and application assessment. This page verifies no mounting measurement or operating clearance and prescribes no torque or hydraulic pressure.

The exact Luan saved row/header and SKF’s exact 22220EK row, mounting explanation, Table 7 boundaries and footnotes were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error. No Luan approved mounting document or actual installation result has been obtained.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22220K
2223581700200052026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22220K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22220K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22220K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22220K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22220K row ↗

    Exact archived row/header read and actually viewed; dimension unit and mounting-method/acceptance data absent. Fresh certificate-name failure on 2026-10-09; archive recheck only.

  2. SKF · Rolling bearings, exact 22220EK and mounting qualifications ↗

    PDF pages 798 and 790–791, printed 796 and 788–789, read, rendered and actually viewed. Exact 100 mm SKF bore, strict interval symbols, method-specific column footnotes and operating-clearance qualification retained. No SKF mounting value assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.