The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22222K
22222K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 110 × 200 × 53 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
A removal plan for 22222K needs the actual shaft or sleeve drawing, not just the K designation.
A replacement purchase can stall when the existing assembly cannot accept the proposed tool. Establish how the bearing is seated, where the tool acts and how release is contained before ordering the replacement and dismounting equipment together.
A tapered bore does not document an oil-injection system.
The retained Luan 22222K row [1] supplies 110/200/53 without a stated dimension unit, 1500/1900 r/min grease/oil entries, 288/465 kN dynamic/static ratings and 7.4 kg reference mass. It gives no shaft drawing, sleeve identity, injection port or removal procedure. Obtain the offered taper and units rather than filling them from another brand.
The separate SKF catalogue [2], printed 798, lists complete 22222EK in its tapered-bore column, with d=110 mm. Its general removal guidance, printed 208, describes injecting oil between the tapered mating surfaces through a supply duct and distribution groove. The method therefore needs a documented path to that interface; the bearing designation alone does not show that the installed shaft provides it.
On printed 209, SKF separately discusses adapter sleeves. The oil-injection option is conditional on the sleeve having the necessary supply ducts and distribution grooves. A seller saying “hydraulic removal” should identify which arrangement is being proposed: a hydraulic puller, a hydraulic nut, oil injection, or a defined combination. These descriptions are not interchangeable equipment specifications.
Check the reaction point and restraint on the same drawing as the tool.
SKF’s adapter-sleeve example for a hydraulic nut concerns a stepped shaft with a spacing collar and calls for a suitable stop against the nut piston. Its tapered-shaft oil-injection example separately warns that the bearing can release suddenly and identifies a shaft-end restraint to limit travel. Keep those conditions with their respective methods; do not omit them from a supplier’s sketch.
When a removal method is proposed
What the proposal must identify
Oil injection at a tapered interface
The relevant shaft or sleeve duct, distribution groove and connection serving that interface, plus the approved release arrangement.
Hydraulic nut on an adapter sleeve
The actual sleeve, shaft/spacer geometry, compatible nut and authorized piston reaction/stop arrangement.
Puller removal
Accessible engagement points, complete load path, available travel and whether the intended condition of the removed bearing permits that method.
Any claim of bearing reuse
How removal forces avoid passing through the rolling elements, and the inspection/acceptance basis after removal.
SKF’s general guidance, printed 207, says dismounting force must not pass through the rolling elements when the bearing is to be used again. Tool access and a possible removal method therefore do not prove that reuse remains acceptable. Agree the intended disposition and an inspection basis before treating the old bearing as a reusable spare.
Ask the supplier or maintenance engineer to mark the proposed tool, reaction faces, oil path where used, restraint and movement envelope on the actual assembly drawing. If the drawing cannot show a required feature, resolve the method or hardware first. This is a procurement review, not an instruction to drill a shaft, pressurize a port or dismantle an assembly.
No Luan-compatible sleeve, hydraulic nut, pressure, puller force, restraint size or successful removal has been established here. The exact archived Luan row/header and SKF’s exact 22222EK row and cited removal sections were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error; the Luan review uses its retained publication.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22222K.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Exact archived row and unitless dimension headers read and actually viewed. No actual shaft/sleeve, injection-path or removal data. Fresh access certificate-name failure on 2026-10-09.
PDF pages 800 and 209–211, printed 798 and 207–209, read, rendered and actually viewed. Exact SKF tapered-bore example; separate shaft/sleeve oil-path conditions, hydraulic-nut reaction, release restraint and force-path qualification for reuse. No SKF hardware or procedure approved for Luan.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies