BearingIndex
THE BEARINGINDEX DIRECTORY

22224K — 120 × 215 × 58 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22224K

22224K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 120 × 215 × 58 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
120 unit unconfirmed
Outside D
215 unit unconfirmed
Width B
58 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

If 22224K is proposed on a hollow shaft, include the shaft section and materials in the review.

An outside shaft diameter does not describe how stiff the bearing seat is. A supplier reviewing a hollow shaft or a sleeve arrangement needs the actual section, seat construction and materials. Do not let a copied fit class stand in for that assessment.

The seat’s outside diameter leaves its hollow section unresolved.

The retained exact Luan 22224K row [1] lists 120/215/58 without a dimension unit, 1300/1700 r/min grease/oil entries, 342/565 kN dynamic/static ratings and 9.2 kg reference mass. It supplies no shaft section, material, sleeve construction or fit criterion.

In SKF’s engineering background [2], printed 146, a hollow shaft under an interference fit deforms more elastically than a same-size solid shaft, reducing fit effectiveness. Its review uses the shaft’s inside/outside diameter ratio and an inner-ring diameter ratio. Knowing only the bearing’s catalogue dimensions leaves an important shaft input missing.

The same catalogue, printed 143, discusses distortion from seat discontinuities or uneven wall thickness and the effect of shaft/housing materials. It also notes that temperature differences and transient conditions can affect a fit. State these conditions in the proposal rather than assuming a solid steel seat simply because the outside diameter matches.

If the bearing is seated on a sleeve, identify that sleeve and its relation to the shaft instead of treating the bearing bore as the shaft diameter. If it is seated directly on a taper, provide the controlled tapered-seat drawing. Establish the actual arrangement before choosing a calculation or mounting guideline.

SKF’s worked 6208 example is not a fit prescription for 22224K.

The printed 146 worked example concerns a 6208 deep-groove ball bearing, a stated hollow-shaft ratio and a selected solid-shaft fit under normal loads. Its resulting m6 choice belongs to those inputs. It does not specify a tapered Luan bearing, prove a sleeve arrangement or authorize machining a 22224K seat to that class.

Use the example to understand why a calculation needs its assumptions. Ask the supplier to return an assessment naming the exact bearing, seat route, shaft/sleeve geometry, materials, load and thermal conditions, and the criterion used to approve the fit or mounting condition. If an input is estimated, have it identified as an estimate rather than hidden in the result.

Provide with the enquiryWhat the reviewer needs to resolve
Section through the bearing seatInside and outside geometry at the seat, wall changes and adjacent features, with confirmed units and drawing revision.
Actual seating routeDirect tapered seat or identified sleeve arrangement; do not substitute a cylindrical-seat example.
Materials and conditionsBearing/shaft/sleeve/housing material information and relevant load and thermal conditions.
Approved resultApplicable machining or mounting requirement, its stated assumptions and the required acceptance evidence for the actual assembly.

A reviewed fit or mounting result must also be considered with the required clearance in operation. No interference amount, seat class, clearance reduction, shaft ratio limit or machining change is prescribed for Luan on this page. The archive does not establish that any actual buyer’s shaft is hollow.

The exact Luan archived row/header and SKF’s hollow-shaft example, structural/material and temperature explanations were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error. No actual shaft drawing, calculation or approved Luan mounting assessment has been obtained.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22224K
342565130017009.22026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22224K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22224K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22224K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22224K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22224K row ↗

    Exact archived row/header read and actually viewed; dimension unit, actual shaft/sleeve and approved fit data absent. Fresh access certificate-name failure on 2026-10-09.

  2. SKF · Rolling bearings, structural/material conditions and hollow-shaft example ↗

    PDF pages 145 and 148, printed 143 and 146, read, rendered and actually viewed. Shaft/housing geometry, materials, thermal conditions and fit effectiveness on hollow shafts; worked 6208 example retained in its own scope, with no result transferred to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.