BearingIndex
THE BEARINGINDEX DIRECTORY

22226W33 — 130 × 230 × 64 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22226W33

22226W33 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 130 × 230 × 64 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
130 unit unconfirmed
Outside D
230 unit unconfirmed
Width B
64 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

“How much grease?” needs a location, a procedure and a time basis for 22226W33.

A first fill in a bearing, a first fill in its housing and a later replenishment are different instructions. Continuous supply adds a time basis. Ask for an approved lubrication sheet for the actual assembly instead of treating all four as one quantity.

Name the component and the event before specifying a grease quantity.

The retained exact Luan 22226W33 row [1] publishes 130/230/64 with no dimension units, grease/oil speed entries of 1200/1600 r/min, dynamic/static ratings of 408/708 kN and reference mass of 11.2 kg. It supplies no initial grease quantity, housing free volume, replenishment interval or continuous delivery rate. The designation alone does not document this offered assembly’s grease route.

The SKF lubrication discussion [2] separates the free volume in a bearing from the free volume in its housing. It describes a commonly complete bearing fill at installation and a partial housing fill. Its method-dependent initial-fill percentages refer to housing free volume; they are not a statement that the same percentage of the bearing should be filled.

Instruction being requestedWhat the instruction must identifyWhy another quantity cannot replace it
Bearing initial fillThe offered bearing’s relevant free volume and approved installation fill.A housing fill percentage has a different volume denominator.
Housing initial fillThe actual housing free volume, seals and inlet arrangement.Bearing catalogue mass does not measure the housing cavity.
Intermittent replenishmentQuantity per replenishment event and the approved interval.An initial fill is not a recurring event quantity.
Continuous supplyQuantity per unit of time and the intended delivery method.A mass without a time basis is not a delivery rate.

SKF’s bearing free-volume estimate is discussed for metallic cages, with a stated limitation for non-metallic cages. Luan’s examined row neither confirms the cage nor states dimension units. No bearing free volume, grease mass, fill percentage, interval or delivery rate has been calculated or approved for Luan 22226W33 here.

Confirm where fresh grease enters and where used grease can leave.

SKF gives different replenishment expressions for supply from the side and supply through holes in the centre of an inner or outer ring. Its diagrams identify those two paths. A supplier therefore needs to identify the actual inlet and bearing construction before choosing the relevant procedure; a W33 label on this Luan directory row is not a verified housing connection or flow path.

The same discussion requires provision for used grease to be purged from the housing. Contacting seals and their orientation affect that path. An automatic lubricator feeding a connection does not by itself demonstrate that grease reaches the intended bearing or that used grease can escape.

Ask the assembly supplier to mark the proposed inlet, the passage to the bearing and the intended purge location on the actual housing/assembly drawing. Have them explain how the actual seal arrangement permits that purge and how delivered lubricant will be checked. Obtain approval of that route before adopting a grease schedule. The SKF discussion is background for these questions; it is not permission to drill or modify this housing, reverse a seal or run the machine during servicing.

A usable supplier instruction needs both quantities and the conditions that make them applicable.

  1. Identify the supplied assembly. Record the complete bearing, drawing revision and confirmed units, actual cage/lubrication features, housing, seals and lubricant specification.
  2. Separate the first fills. State bearing fill and housing fill as separate entries with their component, volume basis or approved measured quantity, and installation procedure.
  3. Define later delivery. For intermittent replenishment, state quantity per event and interval. For continuous supply, state quantity per unit of time. Identify how the selected lubricator’s delivery will be established for the actual installation.
  4. Record the application basis. Include actual speed, load, temperature and contamination conditions, plus the approved inlet and purge route and the method for checking delivery and operating behaviour.

SKF describes deriving a continuous quantity per unit of time by spreading replenishment quantity over the relevant interval. That distinction helps review a proposed instruction; it does not supply either input for the Luan installation. A statement such as “use the catalogue quantity” leaves the event, component and time basis unresolved.

The exact retained Luan row/header and SKF’s quantity and procedure discussion were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error. No current Luan lubrication sheet, housing drawing, tested purge route, selected lubricant or operating result has been obtained.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22226W33
4087081200160011.22026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22226W33.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22226W33

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22226W33.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22226W33 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22226W33 row ↗

    Exact archived row/header read and actually viewed. Dimension units and assembly grease route are unconfirmed; the row does not state grease fill, interval or delivery rate. Fresh certificate-name failure on 2026-10-09.

  2. SKF · Rolling bearings, grease quantity and relubrication procedures ↗

    PDF pages 114–116, printed 112–114, read, rendered and actually viewed. Bearing/housing free volume, method-dependent quantities, intermittent versus continuous delivery and used-grease purge. No numeric lubrication instruction or housing modification approved for Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.