BearingIndex
THE BEARINGINDEX DIRECTORY

22228K — 140 × 250 × 68 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22228K

22228K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 140 × 250 × 68 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
140 unit unconfirmed
Outside D
250 unit unconfirmed
Width B
68 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

The sleeve suffix can matter even when the proposed bearing keeps the same main dimensions.

A replacement review must include the locking device beside the bearing. SKF’s exact 22228 tapered-bore examples use different sleeve variants for open and sealed constructions. This is a reason to request an approved assembly drawing for the Luan offer, not a Luan accessory recommendation.

SKF’s open and sealed combinations do not use the same sleeve designation.

The retained Luan 22228K row [1] gives 140/250/68 without dimension units, 1000/1400 r/min grease/oil entries, 478/805 kN dynamic/static ratings and 14.5 kg reference mass. It does not identify a sleeve, locking nut, washer, seal construction or approved accessory combination.

In the separate SKF bearing-on-adapter table [2], printed 826, the exact pairs are:

Exact SKF bearingSleeve stated for this pairShared dimensions in this SKF combination table
22228 CCK/W33H3128d1 125 mm; D 250 mm; B 68 mm.
22228-2CS5K/VT143H3128Ld1 125 mm; D 250 mm; B 68 mm.

Here d1 belongs to the bearing-on-sleeve arrangement; it is not the bearing’s own bore d. The common main dimensions do not erase the different sleeve designation. Neither SKF pair establishes the actual Luan shaft diameter, sleeve pairing, units or sealing configuration.

SKF’s sleeve designation system, printed 1071, defines L as an adapter sleeve with a lock nut of lower cross-sectional height. It does not define L as a promise of greater sleeve length. Keep the full sleeve code in the quote and drawing rather than replacing H3128L with H3128 on the basis of the shared number.

Review the adjacent hardware against the actual seal geometry.

SKF’s sealed-bearing sleeve discussion, printed 1069 [2], explains that these variants are designed to prevent the locking device from interfering with the seals. Its list includes several suffixes; their existence does not make every variant interchangeable for every sealed bearing.

For comparison, the exact SKF H3128 assembly row, printed 1073, lists KM28 and MB28 under included lock nut and locking device. HMV28E appears under the separate heading associated hydraulic nut. That associated-tool column is not an included-product column and is not a specification of this Luan purchase. The examined H3128 row must also not be used as a parts list for H3128L.

For the Luan proposal, have the supplier identify the complete sleeve, nut and locking device and mark their installed relationship to the actual bearing and seal on the controlled assembly drawing. Review the nut’s envelope, support face, locking arrangement and adjacent space against that construction. A suitable thread or a bearing that enters the housing does not by itself resolve seal interference.

  1. Retain the intended construction. Identify the complete offered bearing and any proposed change from the existing assembly, including whether a seal is being introduced.
  2. Keep accessory variants explicit. Request the full sleeve, nut and locking-device identities. Have the supplier assess retained hardware separately from newly supplied parts.
  3. Resolve every substitution on the drawing. Obtain maker/designer approval of the installed locking and seal clearances before accepting an omitted suffix or a different nut. Do not grind or modify hardware from this catalogue example.

The exact Luan row/header and SKF combination, sleeve-variant explanation and H3128 component headings were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error. No actual Luan sleeve pairing, sealed conversion, locking clearance, supplied accessory list or successful mounting has been verified.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22228K
4788051000140014.52026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22228K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22228K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22228K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22228K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22228K row ↗

    Exact archived row/header read and actually viewed; units and sleeve/locking/seal configuration are unstated. Fresh certificate-name failure on 2026-10-09.

  2. SKF · Rolling bearings, exact 22228 sleeve pairs and locking-device scope ↗

    PDF828 printed826 exact open/sealed H3128/H3128L pairs; PDF1071/1073/1075 printed1069/1071/1073 sealed-sleeve purpose, L definition and included versus associated items. Read, rendered and actually viewed. No SKF accessory or tool approved for Luan; no H3128L parts list inferred from H3128.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.