The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22228W33
22228W33 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 140 × 250 × 68 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
A matching dimension symbol can refer to a different surface in another drawing.
Keep the full part identity and its drawing beside every dimension. An exact NTN 22228 example and a separate SKF sleeve assembly show why copying a d1 field between catalogues can create a wrong shaft requirement.
The same d1 label refers to different geometry in these two specific sources.
The retained exact Luan 22228W33 row [1] publishes d/D/B entries of 140/250/68 with no dimension unit, 1000/1400 r/min grease/oil entries, 478/805 kN dynamic/static ratings and 14.5 kg reference mass. It does not provide a d1 field, groove dimensions or an interface drawing.
The current NTN Americas 22228EAW33 item [2] gives d = 140.000 mm, D = 250.000 mm, B = 68.000 mm and d1 = 163.000 mm. Its linked sectional drawing [3] places d at the bore and d1 at the outside of the inner ring. The 163 mm field is not the bore or the required shaft-seat diameter.
Exact source context
Published d1
Surface identified by that drawing
NTN 22228EAW33 bearing and linked section
163.000 mm
Inner-ring outside diameter; separate from bore d = 140.000 mm.
SKF 22228 CCK/W33 + H3128 adapter assembly
125 mm
Shaft diameter inside the bearing-on-sleeve arrangement, printed 826 [4].
These are different products and drawings, not conflicting dimensions for one interchangeable bearing. The SKF example is a tapered-bore bearing on a specified sleeve; the NTN item is its round-bore bearing. Do not copy either d1 value into the missing Luan field, specify a 163 mm shaft from the NTN label, or infer a 125 mm Luan shaft from the SKF arrangement.
A complete dimension requirement includes the surface and any limit, not just the number.
The NTN item and drawing also distinguish D1 from d1, and distinguish da min and Da max from the bearing’s d and D. Its groove and hole dimensions are labelled W0 and d0. Case, subscripts, the illustrated surface and min/max qualification carry different meanings; reducing all of them to “diameter” discards information needed for an interface review.
For example, NTN’s item lists da min = 154.000 mm and Da max = 236.000 mm. These are separately labelled abutment requirements in its drawing context, not alternative bore and outside-diameter values. Its W0 = 14.000 mm and d0 = 7.000 mm describe the indicated groove/hole geometry of that NTN item. None is verified for the offered Luan 22228W33, and none authorizes machining its shaft or housing.
When asking Luan for the missing drawing, name the purpose of each requested field: bore/seat, ring envelope, support face, shoulder corner, lubrication groove or hole. Ask the supplier to identify that actual surface and its required nominal value, unit and applicable limit or tolerance. Do not use the number of decimal places in a catalogue display as a manufacturing tolerance.
Keep a short field map with the supplier’s approved drawing.
Identify the part and revision. Keep the complete manufacturer designation and the controlled drawing revision with every dimensional requirement.
Mark the actual surface. For each field, record the source symbol and its measured or required surface, including whether it belongs to the bearing, shaft, housing or sleeve assembly.
Retain the qualification. Record the unit and any minimum, maximum, tolerance or measurement condition. Ask for missing information instead of using a different maker’s value.
Resolve the proposed interface. Have the supplier/designer approve the actual mating geometry and replacement arrangement. A field map organizes that review; it does not itself establish fit or interchangeability.
The exact archived Luan row/header, current NTN item and linked drawing, and SKF’s exact adapter assembly row/diagram were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error. No current Luan controlled drawing, groove geometry, shoulder requirement, shaft dimension or successful fit has been verified.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22228W33.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Exact archive row/header independently read and actually viewed. Units and additional drawing fields are unstated. Fresh certificate-name failure on 2026-10-09.
Live exact item read on 2026-10-09; dimensional table actually viewed. d/D/B, d1/D1, groove/hole and separately qualified abutment fields belong to this NTN item, not Luan.
Linked original image read and actually viewed; bore, inner-ring outside diameter, groove/hole and abutment surfaces distinguished. Illustrated variants do not establish Luan construction.
PDF828 printed826 read, rendered and actually viewed; d1=125 mm for exact 22228CCK/W33+H3128 shaft/sleeve context. Separate from NTN ring d1; no SKF pairing or shaft approved for Luan.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies