BearingIndex
THE BEARINGINDEX DIRECTORY

22232K — 160 × 290 × 80 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22232K

22232K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 160 × 290 × 80 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
160 unit unconfirmed
Outside D
290 unit unconfirmed
Width B
80 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A sleeve-mounted 22232K proposal needs its external seal interface drawn separately.

Selecting a bearing and sleeve does not identify the surface where an external seal runs. Keep the bearing bore, sleeve shaft seat and seal counterface distinct, then review movement, contamination and lubricant retention against the actual assembly.

Identify the bearing bore, the sleeve shaft seat and the actual seal surface.

The exact retained Luan 22232K row [1] gives d/D/B entries of 160/290/80 without stated dimension units, 1400/1900 r/min grease/oil entries, 879/1220 kN dynamic/static ratings and 22.8 kg reference mass. It does not identify an approved sleeve assembly, external seal, seal-running surface or housing-cover drawing.

A separate, precisely identified SKF example [2] illustrates the interfaces. Printed 802 lists the tapered-bore 22232 CCK/W33 with bearing bore d = 160 mm. Its adapter-sleeve table, printed 827 with the drawing on 826, lists 22232 CCK/W33 + H 3132 under shaft diameter d₁ = 140 mm. These refer to different surfaces in the SKF assembly; neither number identifies the seal counterface without the actual section drawing.

Interface to markEvidence needed in the offered assembly
Bearing boreThe offered bearing’s controlled bore geometry, fit and mounting requirements.
Sleeve-to-shaft seatThe approved sleeve and actual shaft-seat drawing; do not substitute the bearing bore diameter.
External seal counterfaceThe actual surface contacted by a seal lip, or the mating surfaces forming a non-contact seal; its location and requirements belong to the seal/assembly drawing.

The SKF example does not approve H 3132 for Luan or establish that the actual Luan machine has a 140 mm shaft or seal journal. If the proposal changes the sleeve, shaft steps, seal sleeve or housing cover, review the affected interfaces rather than carrying forward one diameter from the original quotation.

The external seal must accommodate the actual shaft behaviour.

SKF’s external-sealing guidance, printed 195–196 [2], lists lubricant, contaminants, circumferential speed at the seal lip, shaft orientation, misalignment/deflection, run-out, space, frictional heating and maintenance among selection factors. Bearing rotational speed is not by itself the complete seal specification: the actual seal surface and its operating conditions matter.

Its non-contact examples also distinguish arrangements. Helical grooves intended to return oil on a horizontal shaft depend on the rotation direction and require rotation in one direction only. The radial gaps in the axially arranged labyrinth example remain unchanged during axial shaft displacement; the catalogue separately shows inclined labyrinth passages for angular misalignment. These examples explain why a generic label such as “labyrinth seal” does not describe every arrangement’s behaviour.

For the actual 22232K proposal, give the seal designer the expected axial travel, angular misalignment/deflection, run-out and all operating rotation directions. Ask the designer to identify which clearances or contact conditions change through that movement. Reversing operation must be stated before relying on a directional oil-return feature. No groove geometry, allowable movement, seal speed, machining dimension or suitability has been calculated or approved here.

Send one assembly section with separate bearing and seal requirements.

  1. Mark the interfaces. Identify the bearing bore, sleeve shaft seat, external seal counterface and stationary cover in the actual section. Specify which component rotates and retain the drawing revision.
  2. Describe what the seal must do. State lubricant retention and contaminant exclusion needs, actual environment, rotation directions and expected shaft movement. Include temperature, available space and service access.
  3. Resolve responsibility. Request Luan’s confirmation of the bearing/sleeve mounting proposal and the seal supplier’s confirmation of counterface requirements, motion allowance and maintenance procedure. Keep open items visible if the parties review different drawings.
  4. Check revisions before purchase. A replacement sleeve, cover or seal can affect a previously reviewed interface. Obtain a response tied to the revised complete assembly rather than accepting “fits 22232K” as the seal approval.

The archived exact Luan row/header, SKF’s exact bearing and sleeve rows with the interface drawing, and SKF’s seal-selection/non-contact examples were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error. No current Luan sleeve pairing, seal selection, actual assembly geometry or performance test has been verified.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22232K
87912201400190022.82026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22232K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22232K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22232K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22232K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22232K row ↗

    Exact 22232K row and headers independently read and actually viewed; dimension units unstated, 1400/1900 r/min, 879/1220 kN and 22.8 kg. Fresh certificate-name error on 2026-10-09. No verified sleeve or seal interface.

  2. SKF · exact 22232 CCK/W33 + H3132 and external sealing guidance ↗

    PDF804 printed802 exact bearing d160mm; PDF829 printed827 exact H3132 assembly d1 shaft140mm with diagram on PDF828 printed826. PDF197–198 printed195–196 seal criteria, directional helical grooves and labyrinth movement examples. Read, rendered and actually viewed. No SKF hardware pairing, shaft/seal dimension or motion limit assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.