BearingIndex
THE BEARINGINDEX DIRECTORY

22234W33 — 170 × 310 × 86 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22234W33

22234W33 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 170 × 310 × 86 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
170 unit unconfirmed
Outside D
310 unit unconfirmed
Width B
86 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

An oil grade for 22234W33 needs its temperature and operating basis.

The oil-labelled speed entry is not a lubricant recommendation. Ask the bearing and lubricant suppliers to review the proposed oil at the actual duty temperatures, with its base oil and additive package identified.

The 1800 r/min oil entry does not identify an approved oil.

The retained exact Luan 22234W33 row [1] gives d/D/B entries of 170/310/86 without stated dimension units, grease/oil speed entries of 1300/1800 r/min, dynamic/static ratings of 983/1380 kN and reference mass 29.2 kg. The examined row does not name an oil product, ISO viscosity grade, base-oil type, additive package or operating-temperature basis.

If the supplier proposes oil lubrication, request the actual bearing/system requirements and the proposed oil’s technical data. Do not convert the 1800 r/min entry into an oil-grade recommendation or use the unconfirmed historical dimensions to calculate a selection parameter. The operating duty and offered construction still need confirmation.

ISO VG describes viscosity at 40°C; the bearing review needs viscosity at its operating temperature.

SKF’s viscosity discussion and classification table [2], printed 102–103, distinguish actual operating viscosity from rated viscosity used in a lubrication assessment. Its classification table gives ISO grades and kinematic-viscosity ranges at 40°C. For example, the table’s ISO VG 100 row has a mean of 100 mm²/s and a range of 90–110 mm²/s at 40°C. This is an illustration of the grade reference, not a recommendation of VG 100 for Luan 22234W33.

A bare “100” without quantity, unit and temperature is incomplete. It cannot be read as 100 mm²/s at the machine’s hot running condition. Request the identified oil’s viscosity/temperature data and the actual bearing operating-temperature range, then have the supplier evaluate the relevant operating viscosity and required lubrication condition. Preserve the temperature attached to every reported value.

SKF explains that rated viscosity depends on bearing mean diameter and rotational speed and that higher viscosity must be considered against increased friction. Therefore, “use a thicker oil” is not a complete correction for an unassessed duty. No mean diameter, viscosity ratio, speed factor or film condition is calculated from this Luan record.

Keep oil formulation and compatibility in the same review as viscosity.

SKF’s oil-type table on printed 121 [2] distinguishes mineral, PAO, ester and PAG base oils by properties including viscosity index and pressure-viscosity coefficient. Its accompanying text discusses additives, including EP/AW, with application and temperature considerations. A shared viscosity-grade label therefore does not complete the formulation or compatibility review.

Information to retainWhy the supplier needs it
Oil identity and technical dataExact manufacturer/product and revision, base oil, grade and viscosity data with units and reference temperatures.
Actual duty temperaturesStartup and sustained operating conditions, the temperature location/basis and speed/load cycle used in the assessment.
Offered construction and systemConfirmed bearing geometry, cage/seals/materials as applicable, feed arrangement and the components with which the oil must be compatible.
Documented decisionThe suppliers’ assessment of operating viscosity and formulation, its assumptions and any required verification before the revised offer is accepted.

If an oil is replaced by another product of the same grade, retain its full technical identity and ask whether the previous assessment still applies. A grade match alone does not provide the missing temperature behaviour or additive/material compatibility. This page approves no oil brand, base oil, additive, viscosity grade, temperature limit or change interval.

The archived exact Luan row/header and SKF’s operating-viscosity explanation, 40°C grade table and oil-formulation discussion were read and visually checked. Fresh Luan access on 2026-10-09 failed with a certificate-name error. No current Luan lubricant recommendation, actual operating-temperature measurement, oil analysis or successful application test has been obtained.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22234W33
98313801300180029.22026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22234W33.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22234W33

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22234W33.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22234W33 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · retained exact 22234W33 catalogue row ↗

    Exact22234W33 row/header independently read and actually viewed;170/310/86 units unstated,1300/1800r/min,983/1380kN,29.2kg. No grade/formulation/operating-temperature basis in examined row. Fresh certificate-name error on 2026-10-09.

  2. SKF · operating viscosity,40°C grade reference and oil formulation ↗

    PDF104–105 printed 102–103 actual/rated viscosity and ISO-grade table at 40°C; PDF123 printed 121 base-oil properties and additive discussion. Read/rendered/actually viewed. VG 100 example explains a reference-temperature label only; no grade, SKF factor, oil formulation or temperature approval assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.