BearingIndex
THE BEARINGINDEX DIRECTORY

22236K — 180 × 320 × 86 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22236K

22236K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 180 × 320 × 86 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
180 unit unconfirmed
Outside D
320 unit unconfirmed
Width B
86 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A vertical 22236K mounting proposal needs to keep the bearing components centred.

If the shaft or housing must stand vertically during installation, ask how the rings and roller assembly will be supported. Their position during handling can affect the mounting condition; a catalogue clearance or drive-up value does not explain that support arrangement.

The exact row identifies 22236K, but does not supply a vertical assembly procedure.

The Luan 22236K row inspected live on 9 October 2026 [1] lists d/D/B entries of 180/320/86, grease/oil speed entries of 1300/1700 r/min, dynamic/static ratings of 1040/1490 kN and reference mass 30 kg. The dimension headings state no unit. The row does not specify the offered clearance class, taper geometry, mounting tooling or how the components should be supported during installation.

SKF’s separate product table, printed 804 [2], identifies 22236 CCK/W33 in its tapered-bore column, with 180/320/86 mm principal dimensions. That is an explicitly identified SKF construction. It supplies context for reading SKF’s mounting discussion, but does not confirm Luan’s dimension unit, taper, cage or accessory compatibility.

Start the assembly review with the current Luan drawing and the actual machine layout. Record whether the shaft or housing is horizontal or vertical during each stage, including the moment the bearing is supported on its seat and the moment temporary handling equipment is removed.

A downward component displacement can change the mounting condition.

SKF’s spherical-roller mounting discussion on printed 788 [2] explains that the rings and roller complement can become axially displaced during handling, especially with a vertical shaft or housing. It describes the roller complement and a ring moving downwards, eliminating clearance; when the rings subsequently expand or contract under an interference fit, preload can result.

For its described bearings, SKF advises horizontal mounting wherever possible and rotating a ring to align the rollers. Where that is not feasible, it calls for a handling tool or other device to keep the components centrally arranged. These are specific reasons to ask Luan for an approved centring and support procedure for the actual bearing, rather than treating vertical orientation as an irrelevant detail.

The same page separately lists methods for establishing tapered-bore interference, including clearance reduction, axial drive-up and SKF-specific methods. Keeping components centred and establishing the correct fit are distinct requirements. Neither a pressure reading nor a displacement record, by itself, documents the position of the roller assembly during a vertical installation. Do not substitute a centring tool for the maker’s fit procedure, or copy SKF method settings onto Luan.

Make the support sequence visible in the installation record.

StageWhat the supplier’s procedure should resolve
Before seatingActual shaft/housing orientation, the approved bearing support device and how rings and rollers are kept centred without damaging the components.
While establishing the fitThe selected maker-approved method, its own reference and acceptance criteria, and how component position remains controlled throughout the operation.
Before releasing supportWhich checks confirm the assembly is ready, who accepts the recorded result and when temporary support may be removed.
If the position changesThe maker’s response to component displacement or an uncertain measurement, including the conditions for stopping and reviewing the installation.

Send the drawing and proposed sequence to the bearing supplier before work starts. Request an explicit response for the vertical stage if it cannot be avoided. A completed record should identify the actual bearing, procedure revision, orientation, support arrangement and acceptance results; it should not simply say “mounted to catalogue.”

The exact Luan row and table headers were read and visually checked live. SKF’s exact 22236 CCK/W33 entry and its component-position warning were independently read and visually checked. This page specifies no Luan tool geometry, drive-up distance, pressure, residual clearance or preload target. No Luan vertical mounting procedure or actual installation test has been obtained.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22236K
1040149013001700302026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22236K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22236K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22236K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22236K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22236K row, inspected live ↗

    Live page inspected 2026-10-09: exact 22236K row 180/320/86, dimension units unstated; 1300/1700 r/min, 1040/1490 kN, reference mass 30 kg. Table title is 22311MBW33; evidence is the exact row, not that title. No mounting or centring procedure supplied.

  2. SKF · spherical-roller component positioning and exact tapered-bore example ↗

    PDF 790 / printed 788: axial component displacement with vertical mounting, clearance/preload concern, horizontal mounting and central support guidance; separate fit methods. PDF 806 / printed 804: exact 22236 CCK/W33 tapered-bore entry. Both read and visually checked. SKF construction and method settings are not assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.