The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22238
22238 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 190 × 340 × 92 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
A heating temperature for 22238 needs the actual fit and offered construction.
If hot mounting is proposed, have the supplier identify what is heated, the required temperature difference and the limits of every affected component. A general catalogue ceiling is not a mounting target, and a sealed replacement can change the permitted procedure.
The catalogue row does not authorize a heating process.
The exact Luan 22238 row in the page inspected on 9 October 2026 [1] gives d/D/B entries of 190/340/92 without stated dimension units, grease/oil speeds of 1200/1600 r/min, dynamic/static ratings of 1150/1700 kN and reference mass 37.3 kg. It provides no heating target, maximum mounting temperature, heater selection or mounting acceptance procedure.
SKF’s separate table, printed 806 [2], lists 22238 CC/W33 and 22238-2CS5/VT143 in the cylindrical-bore column. Both have 190/340/92 mm principal dimensions, while the latter is shown as a sealed construction. That comparison illustrates why the same principal dimensions cannot establish the heating procedure. It does not identify Luan’s seal, grease or permitted temperature.
Have the supplier identify the exact offered construction before selecting a mounting method. If an offer changes to a sealed or prelubricated version, request a revised procedure addressing those components rather than retaining the open-bearing instruction.
The required temperature difference and the permissible limit answer different questions.
SKF’s hot-mounting discussion on printed 203 [2] says that the required temperature difference between a bearing ring and its shaft or housing depends on the interference and the bearing-seat diameter. It separately gives heating restrictions for open bearings and additional seal/grease constraints for capped bearings. A catalogue maximum is therefore not the temperature automatically required to obtain the actual fit.
For the Luan proposal, request the controlled seat dimensions, fit specification and maker’s calculation or procedure for the required expansion. Have the response identify which component is heated and how its temperature is measured. The unknown dimension units in the Luan source must be resolved through the offered drawing before any dimensional heating calculation is attempted.
SKF also warns against local overheating and recommends even heating, with its induction-heater example. If a supplier proposes another method, ask how uniformity and the applicable component limits are controlled. This is a request for an approved procedure, not permission to heat Luan 22238 to an SKF ceiling or to use an unreviewed heater.
Approve the sequence and acceptance checks with the heating method.
Define the assembly. Identify the exact bearing construction, seat drawing and fit, including the seals and lubricant affected by heating.
Obtain the thermal basis. Request the maker-approved target and limits, what is heated, temperature-measurement arrangement and the method for avoiding local overheating.
Review transfer and seating. Have the responsible installer prepare the handling access and sequence specified by the maker, with the necessary tools and acceptance checks ready.
Record the result. Retain the bearing identity, procedure revision, measured temperatures and the actual seating/fit acceptance. A heater setting alone is not proof of a completed correct installation.
The adjacent SKF section on printed 203 explicitly limits its “adjusted bearing arrangements” discussion to single-row angular-contact ball and tapered-roller arrangements. Its dial-indicator example must not be copied as a generic spherical-roller acceptance method. Obtain the procedure for the actual Luan construction instead.
The exact Luan row/header and SKF’s exact construction comparison and hot-mounting discussion were read and visually checked. No Luan heating temperature, temperature difference, heater model, dwell time or installation result is supplied or calculated here.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22238.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Page accessed 2026-10-09; retained HTML exact 22238 row/header independently inspected and visually checked. 190/340/92 dimension units unstated, 1200/1600 r/min, 1150/1700 kN, reference mass 37.3 kg. No thermal mounting instruction.
PDF 808 / printed 806 exact 22238 CC/W33 and sealed 22238-2CS5/VT143 rows. PDF 205 / printed 203 hot mounting: fit/seat-dependent temperature difference, open versus seal/grease restrictions, uniform heating; adjacent adjusted-arrangement example has restricted bearing-type scope. Read, rendered and visually checked. No SKF thermal setting or adjustment procedure transferred to Luan.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies