BearingIndex
THE BEARINGINDEX DIRECTORY

22238K — 190 × 340 × 92 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22238K

22238K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 190 × 340 × 92 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
190 unit unconfirmed
Outside D
340 unit unconfirmed
Width B
92 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A hydraulic mounting proposal for 22238K must show the thread, reaction surface and oil route.

“Hydraulic mounting” does not identify one universal arrangement. A hydraulic nut generates axial movement; oil injection reduces friction at specified mating surfaces. The actual shaft or sleeve design determines which interfaces are available and how the procedure works.

An adapter-sleeve catalogue example does not supply the hydraulic tool specification.

The exact Luan 22238K row inspected from today’s retained source [1] lists d/D/B entries of 190/340/92 without dimension units, grease/oil speed entries of 1200/1600 r/min, dynamic/static ratings of 1150/1700 kN and reference mass 37.3 kg. It names no approved sleeve, hydraulic nut, injection port or mounting procedure.

SKF’s adapter-sleeve table, printed 827 [2], identifies 22238 CCK/W33 + H 3138 under shaft diameter d₁ = 170 mm. That is a specific SKF combination, distinct from the 190 mm bearing bore in its bearing table. It does not approve H 3138 or any hydraulic equipment for Luan 22238K.

Ask the supplier to identify the actual bearing/seat combination first: direct tapered shaft, adapter sleeve or withdrawal sleeve. Keep the complete component designations and controlled drawing with the proposed tool arrangement. A bearing designation or sleeve number alone does not define the available thread, reaction face or oil duct.

The hydraulic nut’s piston and an injection oil film do different work.

SKF’s mounting explanation and figures 32–34 on printed 204 [2] show hydraulic nuts on a tapered shaft seat, adapter sleeve and withdrawal sleeve. The nut attaches to a shaft or sleeve thread. In the first two examples its annular piston bears against the inner ring; in the withdrawal-sleeve example it bears against a stop on the shaft. Oil supplied to the nut moves its piston axially. The drawing therefore matters to identifying the thread and reaction surface.

The oil-injection discussion on that same page describes a different path: pressurized oil passes through designed ducts and distribution grooves into the interface between bearing and seat, forming a film that separates the mating surfaces and reduces friction. It says these ducts and grooves should be integral to the shaft design, or present in a sleeve equipped for the method.

A hydraulic nut connection is not proof that the shaft or sleeve has suitable oil-injection features. Conversely, an injection port does not identify the tool that supplies axial movement or its reaction arrangement. Request separate identification of both paths where the proposal uses both methods. Do not improvise a port or machine a groove from the catalogue figure.

Have the assembly and tool suppliers review the same drawing.

InterfaceRequired proposal detail
Thread and accessWhich shaft or sleeve carries the hydraulic nut, its controlled thread specification and the space needed to install the approved tool.
Piston reactionThe actual contacted ring or stop, the direction of movement and the supported assembly parts, identified on the section drawing.
Injection path, if usedThe engineered port, ducts and grooves, and exactly which mating interface receives the oil; confirm that the offered components incorporate the features.
Acceptance basisCompatible equipment and the maker-approved procedure, its reference/measurement method and required fit acceptance record.

Keep the procedure’s measurement and acceptance basis with its equipment. SKF separately lists methods of verifying interference on printed 204; the presence of hydraulic equipment itself does not prove the required fit was obtained. Request the offered maker’s actual method, rather than interpreting a gauge reading as universal approval.

The exact Luan row/header, SKF’s exact H 3138 combination and the hydraulic-nut/oil-injection diagrams were independently read and visually checked. This page supplies no hydraulic nut size, pressure, piston stroke, thread tolerance, port geometry or Luan compatibility approval. No actual mounting operation has been tested.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22238K
115017001200160037.32026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22238K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22238K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22238K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22238K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22238K row ↗

    Source acquired 2026-10-09; exact 22238K row/header independently inspected in retained HTML and visually checked. 190/340/92 dimension units unstated, 1200/1600 r/min, 1150/1700 kN, 37.3 kg. No hydraulic tooling or injection-feature approval.

  2. SKF · exact adapter example and distinct hydraulic mounting interfaces ↗

    PDF 829 / printed 827 exact 22238 CCK/W33 + H3138 at shaft d1=170 mm. PDF 206 / printed 204 figures32–36: hydraulic nut thread/piston reaction and separate engineered oil-injection ducts/grooves. Read, rendered and visually checked. No hardware, dimensions, pressure or SKF procedure assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.