BearingIndex
THE BEARINGINDEX DIRECTORY

22240 — 200 × 360 × 98 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22240

22240 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 200 × 360 × 98 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
200 unit unconfirmed
Outside D
360 unit unconfirmed
Width B
98 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 22240 replacement in a changed housing needs the fit reviewed again.

If the housing design, wall thickness or material changes, send those details with the bearing enquiry. A dimensional fit selected for one seat is not automatically valid for another seat with different stiffness or thermal behaviour.

The Luan row describes a bearing entry, not the housing that supports it.

The exact Luan 22240 row [1], independently inspected from the page acquired on 9 October 2026, lists d/D/B entries of 200/360/98 without dimension units, grease/oil speeds of 1100/1500 r/min, dynamic/static ratings of 1290/1910 kN and reference mass 43.2 kg. It names no housing material, wall thickness, seat tolerance or approved fit.

SKF’s separately identified 22240 CC/W33 entry, printed 806 [2], has 200/360/98 mm principal dimensions. That is an exact SKF construction; its dimensions do not confirm the units or construction of the offered Luan bearing. Neither catalogue row identifies the buyer’s housing.

When replacing a bearing and housing together, send the complete housing section and material specification to the assembly designer. If only the bearing changes, still identify the existing seat’s controlled drawing and inspection evidence. A nominal outside-diameter entry alone does not describe the support around the outer ring.

Split seats, uneven support and different materials are fit inputs.

SKF’s fit-selection discussion on printed 143 [2] warns against ring distortion caused by seat discontinuities or uneven wall thickness. For split housings it generally recommends loose fits, and explains that a tighter fit demands higher seat-geometrical accuracy. Its exception for tightly machined SKF plummer-block housings is not approval of an unidentified split housing.

The same discussion distinguishes thin-walled housings and hollow shafts from robust cast-iron housings and solid shafts. It also says that shaft or housing materials other than steel or cast iron may require different fits because of their strength and thermal properties. These are reasons to submit the actual design and material for assessment, not to choose a tighter fit from the bearing number.

Keep “split”, “thin-walled” and “different material” as drawing-supported conditions rather than guesses about the installation. Ask the designer to state which assumptions support the selected fit and what must be rechecked if the seat support, wall section or material changes. No tolerance zone or machining allowance is assigned to Luan 22240 here.

Review the temperatures and geometry with the dimensional fit.

SKF’s temperature discussion on printed 143 [2] explains that different ring and seat temperatures can affect fits: an inner ring may loosen on its shaft, while outer-ring expansion can restrict desired axial movement in a housing. It calls for both transient and steady-state conditions to be considered. A single ambient-temperature measurement does not describe the entire operating fit.

Review inputEvidence for the actual assembly
Seat constructionHousing section, split arrangement if present, wall thickness/support and any discontinuities around the seat.
MaterialsSpecified shaft and housing materials, with the designer’s relevant strength and thermal-property basis.
Operating conditionsLoad magnitude/direction and temperatures of the rings and adjacent parts during start-up and steady operation, or identified unresolved inputs.
AcceptanceApproved fit, seat-geometrical requirements and inspection procedure for the actual construction, plus how the assembled result is checked.

Have the bearing supplier and housing/machine designer resolve the same drawing revision. A fit response should state its assumptions and remaining conditions; a catalogue bearing rating is not an assessment of housing stiffness or material behaviour.

The exact Luan row/header, exact SKF bearing entry and SKF’s seat-design/material/temperature discussion were read and visually checked. No actual housing condition, temperature difference, fit calculation or installed result has been verified for Luan 22240.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22240
129019101100150043.22026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22240.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22240

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22240.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22240 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22240 row ↗

    Source acquired 2026-10-09; exact plain 22240 row/header independently inspected and visually checked. 200/360/98 units unstated,1100/1500 r/min,1290/1910 kN,43.2 kg. No housing or fit approval.

  2. SKF · exact bearing context and seat design/material fit factors ↗

    PDF808 / printed806 exact 22240 CC/W33 entry. PDF145 / printed143: seat discontinuities/uneven walls, split-housing accuracy, thin-wall/hollow distinctions, material strength/thermal properties and transient/steady fit temperatures. Read, rendered and visually checked. No SKF fit or housing approval assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.