BearingIndex
THE BEARINGINDEX DIRECTORY

22240K — 200 × 360 × 98 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22240K

22240K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 200 × 360 × 98 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
200 unit unconfirmed
Outside D
360 unit unconfirmed
Width B
98 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A sleeve combination for 22240K still needs an axial-location drawing.

Tell the supplier where the bearing must sit and what axial loads its supports must accommodate. A sleeve-only arrangement and a sleeve located against a distance ring have different conditions of use; neither follows automatically from the K designation.

A published sleeve identifies a combination, not the axial position in the machine.

The exact Luan 22240K row [1], independently inspected from the source acquired on 9 October 2026, lists d/D/B entries of 200/360/98 without dimension units, grease/oil speeds of 1100/1500 r/min, dynamic/static ratings of 1290/1910 kN and reference mass 43.2 kg. It names no approved sleeve, distance ring, axial-position tolerance or retention capacity.

SKF’s separate adapter table, printed 828 [2], lists 22240 CCK/W33 + H 3140 under shaft diameter d₁ = 180 mm. This is a specific SKF combination. It does not approve those components or that shaft diameter for Luan 22240K, and it does not define where the bearing sits in the buyer’s machine.

Include the actual axial reference in the enquiry: the controlled drawing location, what it is measured from and which component supports the inner ring. Keep that positioning requirement separate from the fit and from the complete locking-parts list.

A sleeve-only arrangement has stated conditions; a distance ring changes the support.

SKF’s axial-location discussion on printed 178 [2] lists a sleeve-only arrangement where precise axial positioning is not required and the axial loads do not exceed friction between sleeve and shaft. It separately describes an adapter sleeve with a distance ring where precise positioning is needed or elevated axial loads occur. The actual figures 18 and 19 on printed 179 show those distinct arrangements.

The same section separately describes a lock nut on a direct tapered seat and a withdrawal sleeve with a distance ring or shaft shoulder and lock nut. These are different physical supports. A parts list saying “bearing and sleeve” leaves the positioning and axial reaction unresolved.

Use the distinction to request an assessment of the actual Luan proposal. Do not treat the bearing’s 1910 kN static rating as the permissible axial retention load of the sleeve/shaft interface, distance ring or locking components. The proposal needs the actual axial loads and the supplier/designer’s applicable retention and support basis.

Draw the supports and agree how the position will be accepted.

Question to resolveEvidence in the assembly proposal
Where must it sit?Controlled axial location and datum, with any required positioning tolerance specified by the machine designer.
What supports the ring?Actual shoulder/distance ring/locking arrangement and the contacted surfaces, with the complete approved components identified.
What load does it retain?Axial loads and direction for relevant duty cases, with an assessment for the actual sleeve/shaft and support arrangement.
How is it accepted?Maker-approved mounting and locking instructions, position/fit checks and the recorded acceptance criteria.

SKF’s abutment discussion on printed 178 also requires clearance between rotating and stationary parts and addresses shaft fillets and spacing collars. Have the actual support geometry reviewed with the location arrangement; do not adopt the drawn collar as a ready-made part for Luan.

The exact Luan row/header, exact SKF sleeve example and axial-location text and figures were independently read and visually checked. No axial retention allowance, position tolerance, distance-ring dimension, nut torque or Luan component compatibility is calculated or approved here. No actual installed position has been inspected.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22240K
129019101100150043.22026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22240K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22240K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22240K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22240K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22240K row ↗

    Source acquired 2026-10-09; exact 22240K row/header independently inspected and visually checked. 200/360/98 units unstated,1100/1500 r/min,1290/1910 kN,43.2 kg. No axial-location or sleeve approval.

  2. SKF · exact sleeve combination and axial-location arrangements ↗

    PDF830 / printed828 exact 22240 CCK/W33 + H3140 at shaft d1=180 mm. PDF180–181 / printed178–179 axial-location conditions, sleeve-only versus distance-ring arrangement and figures17–21. Text and actual figures read/rendered/visually checked. No SKF parts, retention capacity or location tolerances assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.