BearingIndex
THE BEARINGINDEX DIRECTORY

22244 — 220 × 400 × 108 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22244

22244 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 220 × 400 × 108 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
220 unit unconfirmed
Outside D
400 unit unconfirmed
Width B
108 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 22244 replacement enquiry should retain the inspection evidence, not only the damaged part number.

If a used bearing is being replaced after an abnormal event, preserve the observed sequence and physical evidence for the responsible investigator. Confirm the replacement specification separately; buying the same number does not resolve an unidentified cause.

The Luan catalogue row is not an inspection result for the removed bearing.

The exact Luan 22244 row [1], independently inspected from the source acquired on 9 October 2026, gives d/D/B entries of 220/400/108 without dimension units, grease/oil speed entries of 1000/1400 r/min, dynamic/static ratings of 1560/2260 kN and reference mass 59.5 kg. It supplies no inspection report, failure cause or repair eligibility statement.

SKF’s separately identified 22244 CC/W33 entry, printed 808 [2], gives 220/400/108 mm principal dimensions. That remains a distinct SKF construction. Neither entry identifies what was actually installed in the machine, its operating history or the correct replacement requirements.

Retain the complete removed markings, position and available purchase/drawing records. In the replacement enquiry, distinguish the observed installed part from the newly offered construction. If the removed identity or original drawing is uncertain, keep that uncertainty visible for the supplier and investigator.

Collect evidence with its position and sequence before it loses context.

SKF’s inspection guidance on printed 212–213 [2] calls for photographs throughout the inspection process, documenting bearing, lubricant and machine condition. It recommends representative grease samples and comparison with fresh grease; its preparation discussion differentiates oil samples from a sump/reservoir and grease samples from positions within and around an open bearing.

Use those distinctions when arranging the investigation with the responsible maintenance team: label where and when each observation or sample was taken, and keep the exact lubricant identity and service history. A sample without its location or an isolated photograph after cleaning leaves important context unresolved.

EvidenceContext to retain
PhotographsBearing identity/position and inspection stage; include the surrounding seals, housing and machine as relevant.
Lubricant samplesSampling location/time, lubricant product and relevant maintenance history; have the investigator specify sampling and analysis.
ObservationsWhat was seen or measured, by whom and under which conditions, keeping observations distinct from proposed explanations.
Removed partsIdentity, orientation/position where recorded and the investigator’s handling/preservation instructions.

This is an evidence brief for qualified personnel, not a disassembly or cleaning procedure. SKF’s detailed cleaning section has a defined open-bearing/housing context; no solvent, chemical mixture or service operation is prescribed for the actual Luan assembly here.

The first symptom, repair eligibility and replacement approval are separate findings.

SKF’s troubleshooting discussion on printed 213 [2] warns that some symptoms can be misleading and may result from secondary damage. It stresses analysing the symptoms first observed in the application. Record the earliest known event and subsequent sequence rather than treating the final surface appearance as proof of one cause.

The same page says certain medium-size and large bearings are suitable for reconditioning. That does not establish that a particular used Luan 22244 is repairable, or that SKF provides a service for it. Request a qualified service provider’s assessment of the actual part, scope, acceptance requirements and any limitations before considering repair.

For a new replacement, have the bearing supplier and machine designer confirm the current complete specification and any changes required by the investigation. Keep the investigator’s established findings, proposed corrective actions and still-unresolved questions with the enquiry. A repeat order should not be presented as proof that the operating problem has been solved.

The exact Luan row/header, exact SKF bearing entry and inspection/troubleshooting sections were independently read and visually checked. No damaged Luan bearing, actual sample, root cause, repair capability or completed replacement result has been verified.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22244
156022601000140059.52026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22244.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22244

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22244.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22244 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22244 row ↗

    Source acquired 2026-10-09; exact plain 22244 row/header independently inspected and visually checked. 220/400/108 units unstated,1000/1400 r/min,1560/2260 kN,59.5 kg. No inspection, cause or repair eligibility evidence.

  2. SKF · exact bearing context, inspection evidence and troubleshooting scope ↗

    PDF810 / printed808 exact 22244 CC/W33 entry. PDF214–215 / printed212–213 photographs/sample context, inspection scope, secondary damage versus first symptoms, and certain bearings eligible for reconditioning. Read/rendered/visually checked. No actual Luan fault, chemical cleaning instruction or repair-service approval inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.