BearingIndex
THE BEARINGINDEX DIRECTORY

22244K — 220 × 400 × 108 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22244K

22244K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 220 × 400 × 108 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
220 unit unconfirmed
Outside D
400 unit unconfirmed
Width B
108 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

For an oil-injection proposal, ask which sleeve surface each inlet actually feeds.

A sleeve described only as hydraulic leaves important interfaces unresolved. Request its complete designation and oil-path drawing, then check that the installation gives access to the specified inlets and compatible equipment.

The published example includes OH and H; those characters carry information.

The exact Luan 22244K row [1] lists d/D/B entries of 220/400/108 without dimension units, grease/oil speeds of 1000/1400 r/min, dynamic/static ratings of 1560/2260 kN and reference mass 59.5 kg. It does not specify an oil-injection sleeve or its oil supply connections.

SKF’s independent adapter table, printed 828 [2], lists 22244 CCK/W33 + OH 3144 H at shaft diameter d₁ = 200 mm. This is a specific SKF combination, not approval of the same sleeve or shaft diameter for Luan 22244K. Keep the OH prefix and H suffix when discussing that example: omitting them hides the oil-injection variant.

Ask the supplier to identify the actual proposed bearing and sleeve together on an approved assembly drawing. The catalogue example helps identify questions; it cannot establish Luan compatibility, connection dimensions or mounting settings.

SKF’s H and B/HB variants do not distribute oil to the same surfaces.

SKF’s oil-injection sleeve discussion and actual Table 1 on printed 1068 [2] distinguish the inlet end, duct count and groove location. For metric sleeves with bore diameter at least 200 mm, the table gives these differences:

SKF variantSupply ductsInlet endDistribution grooves
OH .. HOneThreaded endOutside surface
OH ..OneEnd opposite the threaded sectionOutside surface
OH .. BTwoEnd opposite the threaded sectionBore and outside surface
OH .. HBTwoThreaded endBore and outside surface

The two-duct statement has a size condition: the same table lists one duct for all four variants below 200 mm bore. Its footnote also says that, where there are two ducts, each feeds one distribution groove; an arrow beside the inlet on the sleeve side face identifies which groove it feeds.

For the SKF OH 3144 H example, the H variant describes an outside-surface groove with supply at the threaded end. Do not assume that one inlet also feeds the sleeve bore or that substituting B/HB preserves access in an existing housing. Have the supplier mark the actual proposed oil paths and accessible inlet end on the Luan assembly drawing.

Resolve the connections and procedure before buying the assembly.

  1. Identify the complete components. Obtain the approved bearing, sleeve and locking-parts list with controlled drawings and units. Confirm that oil injection is supported for the proposed assembly.
  2. Trace each oil path. Mark inlet, duct and distribution groove, including the surface supplied. For multiple ducts, identify their separate functions rather than treating them as interchangeable connections.
  3. Check access and equipment. Show the inlet end in the actual machine assembly. Request the specified connection details and compatible equipment; nearby nuts, shoulders and housing parts must be included in the access review.
  4. Agree the applicable operation. Ask for the maker-approved mounting or dismounting instructions and acceptance records. A sleeve variant table supplies neither pressure settings nor a complete procedure.

The exact Luan row/header, SKF bearing/sleeve combination and oil-injection table with its actual figures and footnote were independently read and visually checked. No pressure, port thread, tool designation, displacement or Luan sleeve compatibility is assigned here. No installed assembly or oil-path performance has been tested.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22244K
156022601000140059.52026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22244K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22244K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22244K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22244K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22244K row ↗

    Source acquired 2026-10-09; exact 22244K row/header independently read and visually checked. 220/400/108 units unstated;1000/1400 r/min;1560/2260 kN;59.5 kg. No sleeve or injection approval.

  2. SKF · exact adapter combination and oil-injection sleeve variants ↗

    PDF830 / printed828 exact 22244 CCK/W33 + OH3144H, shaft d1=200 mm. PDF1070 / printed1068 oil-injection sleeve text and Table1: variant-specific inlets/ducts/grooves, size conditions and footnote. Actual figures rendered and visually checked. SKF examples do not approve Luan components or installation settings.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.