BearingIndex
THE BEARINGINDEX DIRECTORY

22244W33 — 220 × 400 × 108 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22244W33

22244W33 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 220 × 400 × 108 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
220 unit unconfirmed
Outside D
400 unit unconfirmed
Width B
108 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A grease dropping point does not approve the operating temperature of 22244W33.

When a quotation includes a grease temperature range, ask what its endpoints mean. Cold starting, sufficient oil release and sustained hot operation are different checks; a broad range on a datasheet leaves those conditions unresolved.

The bearing table contains no grease product or temperature approval.

The exact Luan 22244W33 row [1] lists d/D/B entries of 220/400/108 without dimension units, grease/oil speeds of 1000/1400 r/min, dynamic/static ratings of 1560/2260 kN and reference mass 59.5 kg. It supplies no named grease, cold-start limit, dropping point or sustained operating-temperature limit.

SKF’s separate product table on printed 808 [2] contains 22244 CC/W33 under cylindrical-bore spherical roller bearings, with 220/400/108 mm dimensions. That is a specific SKF entry. Neither its construction nor any SKF grease approval is assigned to the Luan offering.

Request a grease proposal tied to the complete Luan construction and actual machine conditions. The source’s grease speed figure does not establish that an unspecified grease can lubricate the bearing at the buyer’s temperature.

Ask whether each endpoint describes torque, oil release, grease life or dropping point.

SKF’s temperature discussion and actual Diagram 4, printed 117–118 [2], distinguish four boundaries. They explain why a single broad temperature range is insufficient:

Boundary in SKF’s frameworkWhat it assessesQuestion for the grease supplier
LTL — low temperature limitLow-temperature frictional torque testing.What test and bearing conditions support the claimed cold-start endpoint?
LTPL — low temperature performance limitSufficient oil bleeding; SKF cites DIN 51817.Does the claimed lower performance limit cover this roller-bearing duty?
HTPL — high temperature performance limitGrease life; SKF uses its R0F grease life test.What life/performance evidence supports sustained operation at the proposed temperature?
HTL — high temperature limitLoss of grease consistency, determined by dropping point, ISO 2176.Is a quoted upper endpoint merely the dropping point rather than a reliable operating-performance limit?

SKF places reliable performance between LTPL and HTPL. Its discussion treats the adjacent lower and upper zones as unreliable for sustained service: low-temperature oil bleeding is insufficient, while grease degradation accelerates above HTPL. A dropping-point result therefore cannot serve as the continuous operating limit.

The actual Diagram 5 footnote identifies its LTPL values as valid for roller bearings and gives approximately 20 °C lower values for ball bearings. This is a distinction in SKF’s grease framework, not permission to subtract 20 °C from another supplier’s datasheet for Luan. SKF also warns that performance-limit definitions are not internationally standardized; have the actual grease supplier explain and approve its own evidence.

Send the temperature cycle, then request a decision for that cycle.

  1. Describe the start. State the cold-start temperature, the expected warm-up duration and how the machine is loaded during warm-up. Do not collapse a short start and sustained cold operation into one minimum-temperature figure.
  2. Describe normal running and excursions. Provide the expected bearing temperature, measurement location and duration of hotter periods. Keep ambient, housing and estimated bearing temperatures identifiable.
  3. Identify the grease and its evidence. Obtain the exact commercial product, current data and the meaning of its limits. Request roller-bearing suitability and a supplier decision for the actual temperature cycle.
  4. Agree acceptance and follow-up. Have the machine/bearing/grease suppliers specify applicable commissioning and monitoring criteria, with review of unexpected temperature behavior. Do not use the dropping point as an alarm or shutdown setting.

The exact Luan row/header, SKF exact model entry, temperature text, diagrams and footnote were independently read and visually checked. No grease is selected, no operating or alarm temperature is calculated, and no cold-start or grease-life test has been performed on a Luan 22244W33 assembly here.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22244W33
156022601000140059.52026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22244W33.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22244W33

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22244W33.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22244W33 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22244W33 row ↗

    Source acquired 2026-10-09; exact row/header independently read and visually checked. 220/400/108 dimension units unstated;1000/1400 r/min;1560/2260 kN;59.5 kg. No grease product or temperature approval.

  2. SKF · exact bearing entry and grease temperature performance limits ↗

    PDF810 / printed808 exact cylindrical-bore 22244CC/W33. PDF119–120 / printed117–118 four temperature boundaries, Diagram4/5 and roller-bearing footnote; actual rendered diagrams viewed and text read. Other-supplier definitions require care. No SKF grease or temperature limit approved for Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.