The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22308
22308 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 40 × 90 × 33 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
A 22308 replacement needs more than matching catalogue numbers.
Ask which complete design is being offered. The independently checked SKF examples show why equal dimensions and load ratings can still hide a duty difference, while a sealed version can change the required width.
Start with the exact Luan row, then ask for the offered design.
The Luan 22308 row [1] lists d/D/B entries of 40/90/33 without dimension units, grease/oil speed ratings of 4000/5000 r/min, dynamic/static ratings of 73.5/90.5 kN and reference mass 1.03 kg. Its header and exact row were independently checked. It supplies no complete internal design, cage specification or vibration qualification.
The nearby K and W33 rows are separate designations. Request the complete offered Luan drawing rather than selecting a variant from the numerical entries alone. Confirm dimension units before using the historical entries to approve a seat or replacement.
SKF’s ordinary, vibratory and sealed examples answer different questions.
Ordinary E design; do not assign its ratings to Luan.
22308 E/VA405
40/90/33
155/140
Vibratory variant; equal envelope and basic ratings do not remove the duty distinction.
BS2-2308-2RS/VT143
40/90/38
155/140
Sealed example with greater width; examine the actual axial space and construction.
SKF’s stated ratings differ from the exact Luan publication. Keep each figure attached to its maker and full designation. Neither a larger rating nor a matching numerical size establishes cross-brand application approval; request the actual offered design and the applicable rating/selection basis.
Equal basic ratings do not establish equal acceleration capability.
SKF’s vibratory-application discussion on printed 779 [2] explains extra roller and cage demands and distinguishes two acceleration modes: rotating or rapidly varying acceleration fields, and impact-induced linear acceleration. It says its vibratory bearings tolerate higher accelerations than corresponding standard bearings, with capability depending on lubricant and acceleration mode.
The discussion also scopes the permissible acceleration values in its product tables to oil-lubricated bearings. Do not transfer that qualification to a grease-lubricated Luan proposal or infer it from the 22308 number. Where the buyer’s machine has vibration, impact or rapid starts/speed changes, provide those actual conditions for a construction-specific assessment.
Have the supplier explain the proposed replacement in the actual assembly.
Identify both bearings fully. Send the existing bearing designation and drawing, and ask for the complete offered Luan construction and current controlled drawing with units.
Resolve the physical interfaces. Compare bore type, outside diameter, width, shoulders, fillets and seal/abutment arrangement against the actual machine drawing. Do not use the sealed SKF example as a same-width replacement.
Compare duty and evidence. Keep maker-specific load and speed figures separate. Add the actual lubrication and acceleration conditions when relevant, and request a written suitability assessment.
Record the decision. Obtain the approved component and mounting/acceptance basis. An unqualified statement that “22308 is interchangeable” leaves the differences above unanswered.
The exact Luan row/header, actual SKF variant table and vibratory text/figures were independently read and visually checked. No Luan cage, sealing, acceleration allowance or cross-brand interchange is approved here. No comparative test or installed assembly inspection has been performed.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22308.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Source acquired 2026-10-09; exact plain22308 row/header independently inspected and visually checked.40/90/33 units unstated;4000/5000 r/min;73.5/90.5 kN;1.03 kg. No full design or vibration qualification.
PDF794 / printed792 actual22308E,22308E/VA405 and BS2-2308-2RS/VT143 rows, units/ratings/widths. PDF781 / printed779 actual vibratory designs, modes and oil-lubrication scope. Text and rendered table/figures read and viewed. No SKF values or approval assigned to Luan.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies