BearingIndex
THE BEARINGINDEX DIRECTORY

22309 — 45 × 100 × 36 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22309

22309 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 45 × 100 × 36 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
45 unit unconfirmed
Outside D
100 unit unconfirmed
Width B
36 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Ask what “self-aligning” permits in the actual 22309 arrangement.

A catalogue angle needs its load, motion and construction conditions. Describe whether the direction of the shaft deflection stays fixed relative to the outer ring, and have the bearing and housing reviewed together.

The exact Luan row does not give an allowable misalignment angle.

The Luan 22309 row [1] lists d/D/B entries of 45/100/36 without dimension units, grease/oil speed ratings of 3600/4500 r/min, dynamic/static ratings of 108/140 kN and reference mass 1.4 kg. It does not specify a misalignment angle, seal construction or a load condition for such an allowance.

SKF’s independent table on printed 792 [2] lists cylindrical-bore 22309 E at 45/100/36 mm. Its separate sealed example BS2-2309-2RS/VT143 is 45/100/42 mm. These are SKF constructions, not approvals or specifications for Luan. Confirm the actual offered design and units before evaluating the buyer’s arrangement.

SKF’s 3° series guideline has conditions; it is not a universal machine tolerance.

SKF Table 6 on printed 780 [2] lists a 3° guideline for its 223 series. The adjoining bearing-data section on printed 781 qualifies that table for light to normal loads, P ≤ 0.1 C, and a constant position of misalignment relative to the outer ring. It also says the usable allowance depends on the bearing arrangement and housing abutments.

That condition is about the misalignment position relative to the outer ring. It cannot be decided simply by describing a shaft as rotating or stationary. SKF separately describes rotating shaft deflection and deflection-compensating rolls with a stationary, non-straight shaft as examples where the misalignment position is not constant relative to the outer ring.

SKF conditionWhat its discussion establishesWhat the buyer should provide
Constant position relative to the outer ringTable6 guidelines have load and arrangement conditions.Load cases, ring motion and actual support/abutment geometry.
Changing position relative to the outer ringAdditional sliding can restrict allowance to a few tenths of a degree.Deflection direction through the operating cycle, with the actual duty described.
Sealed bearingIts stated limit is 0.5° to avoid detrimental sealing effects.Complete seal construction and supplier-approved alignment basis.

These statements show why the 3° figure cannot be applied without its conditions or copied to a sealed proposal. They do not establish a Luan 22309 allowable angle. Obtain the Luan maker’s assessment of the actual load, motion, construction and arrangement; do not calculate a threshold from the historical row here.

Describe the deflection and supports so the supplier can assess the right condition.

  1. Show the actual arrangement. Include bearing seats, housing abutments, seals and nearby components. Confirm the complete offered bearing construction.
  2. Describe the misalignment through the cycle. Identify its magnitude and direction from design or measurement, what they are referenced to and whether the position changes relative to the outer ring.
  3. Attach the load and operating cases. Give the conditions for which the allowance is requested. Keep any catalogue example separate from the actual machine’s assessment.
  4. Agree the applicable acceptance. Request a written maker/designer decision and alignment/commissioning criteria for this arrangement. Self-aligning construction alone is not an acceptance record.

The exact Luan row/header, SKF exact model entries, actual Table 6, deflection figure and adjacent conditions were independently read and visually checked. No Luan permissible angle, load threshold, seal limit or actual alignment is calculated or certified here. No shaft-deflection measurement or installed test has been performed.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22309
108140360045001.42026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22309.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22309

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22309.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22309 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22309 row ↗

    Source acquired 2026-10-09; exact plain22309 row/header independently read and visually checked.45/100/36 dimension units unstated;3600/4500r/min;108/140kN;1.4kg. No permissible misalignment or seal design.

  2. SKF · exact 22309 entries and conditional misalignment guidelines ↗

    PDF794 / printed792 exact cylindrical22309E and sealedBS2-2309-2RS/VT143. PDF782–783 / printed780–781 actual Table6, rotating-deflection Figure14 and load/relative-position/arrangement/seal conditions; rendered pages actually viewed and text read. No SKF angle or construction assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.