BearingIndex
THE BEARINGINDEX DIRECTORY

22309K — 45 × 100 × 36 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22309K

22309K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 45 × 100 × 36 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
45 unit unconfirmed
Outside D
100 unit unconfirmed
Width B
36 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 22309K kit quotation should name the sleeve, nut and locking device separately.

Ask for a component list and assembly drawing. A bearing/sleeve combination does not describe every supplied part, and a design suffix on the bearing is not the same instruction as a suffix on the sleeve.

Luan’s exact bearing row leaves the supplied kit unresolved.

The exact Luan 22309K row [1] lists d/D/B entries of 45/100/36 without dimension units, grease/oil speeds of 3600/4500 r/min, dynamic/static ratings of 108/140 kN and reference mass 1.4 kg. It does not identify a sleeve, lock nut, washer, clip or other locking device.

SKF’s independent adapter table on printed 824 [2] lists 22309 EK + H 2309 at shaft d₁ = 40 mm, with D = 100 mm and bearing B = 36 mm. This is a specific SKF combination, not approval of those parts or shaft diameter for Luan. The bearing’s width and mass also do not specify a complete kit’s envelope or supplied contents.

E on a bearing and E on an adapter sleeve describe different things.

SKF’s bearing designation system on printed 790 [2] uses E for an optimized internal design. Its separate adapter-sleeve discussion on printed 1069 uses sleeve variants and locking assemblies to address physical interference. Do not interpret the E in the bearing designation 22309 EK as a sleeve or nut instruction.

The sleeve section identifies special variants for sealed spherical roller and sealed self-aligning ball bearings to prevent the locking device interfering with the seals. It lists sleeve suffixes E, EL, EH, L and TL. For EL and EH assemblies it distinguishes KMFE .. L and KMFE .. H lock nuts with respectively lower and higher abutment diameters than the standard KMFE nut.

These are SKF component definitions. They do not prove that a particular sealed Luan replacement or corresponding sleeve variant exists or is approved. If a quotation changes construction or locking components, request its actual clearance drawing and maker approval instead of adding a suffix to H 2309 yourself.

Separate component identity, physical interfaces and locking instructions.

SKF’s basic sleeve discussion on printed 1067 [2] states that its sleeves are supplied complete with a nut and locking device, illustrating a washer, clip and plate as distinct arrangements. That SKF supply statement does not define the contents of a Luan quotation.

Line in the proposalEvidence to request
BearingFull maker designation and controlled drawing with units, including the actual open/sealed construction.
SleeveComplete approved sleeve designation, shaft interface and assembled support/envelope drawing.
Lock nut and locking deviceSeparate approved identities and quantities, their contacted surfaces, relevant clearance and applicable locking instructions.
Delivered kitAgreed included components, identification and the record needed to resolve missing or substituted parts.

Where seals are present, have the supplier show their relationship to the actual nut and locking device. A shared nominal size or matching thread does not by itself settle abutment geometry, sealing clearance or suitability of the complete assembly.

Approve the assembly drawing and parts list together.

Send the actual machine arrangement with the enquiry. Obtain the approved bearing, sleeve, nut and locking device as one proposal, with mounting/removal access and positioning requirements addressed. Agree how the supplied parts and maker-required mounting/locking records will be checked.

The exact Luan row/header, SKF exact adapter combination, bearing E definition, basic sleeve figures and special sealed-bearing assembly text/figures were independently read and visually checked. No Luan sleeve, nut, seal clearance, torque, washer substitution or kit contents is inferred here. No physical assembly or delivered kit has been inspected.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22309K
108140360045001.42026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22309K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22309K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22309K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22309K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22309K row ↗

    Source acquired 2026-10-09; exact K row/header independently read and visually checked.45/100/36 units unstated;3600/4500r/min;108/140kN;1.4kg. No kit or locking-part specification.

  2. SKF · exact 22309 EK combination and component-specific definitions ↗

    PDF826 / printed824 exact22309EK + H2309 at shaft40mm, actual row/sketch inspected. PDF792 / printed790 bearing E definition. PDF1069 / printed1067 basic nut/locking-device figures and PDF1071 / printed1069 sealed-bearing sleeve variants and EL/EH nut-abutment distinctions; actual rendered pages read/viewed. No Luan component compatibility or supply approval.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.