BearingIndex
THE BEARINGINDEX DIRECTORY

22309W33 — 45 × 100 × 36 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22309W33

22309W33 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 45 × 100 × 36 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
45 unit unconfirmed
Outside D
100 unit unconfirmed
Width B
36 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

An oil speed rating does not establish when to change the oil for 22309W33.

Identify the lubrication system before requesting a maintenance interval. An oil-bath calendar guideline and a circulation-system oil-quality decision use different evidence; the supplier needs the actual operating conditions.

Luan publishes an oil speed figure, not an oil maintenance schedule.

The exact Luan 22309W33 row [1] lists d/D/B entries of 45/100/36 without dimension units, grease/oil speed ratings of 3600/4500 r/min, dynamic/static ratings of 108/140 kN and reference mass 1.38 kg. It supplies no oil product, operating temperature, inspection method or change interval.

SKF’s independent model table on printed 792 [2] lists cylindrical-bore 22309 E at 45/100/36 mm. That SKF entry does not approve the Luan construction or supply a maintenance instruction for the buyer’s machine. Request the complete offered construction and actual lubrication arrangement before agreeing maintenance.

Keep the conditions attached to an oil-change recommendation.

SKF’s oil-change discussion, printed 121 [2], makes the interval dependent on operating conditions and oil type. It gives distinct guidance for oil bath and oil circulation:

Arrangement in SKF’s discussionStated basisQuestion for the actual proposal
Oil bathIts general annual-change guideline is conditional on operating temperature not exceeding 50 °C. Higher temperature or heavy contamination typically requires more frequent changes.Which actual temperature, oil and contamination conditions support the maker’s proposed interval?
Oil circulationAssess oil quality, including oxidation, water and abrasive particles. Removing particles and water can extend oil life.What oil-quality inspection, sample basis and decision criteria will determine changes for this circuit?

The annual guideline is not a universal instruction for Luan 22309W33. Nor does installing filtration prove that the circulating oil remains suitable: the quality assessment includes oxidation and water as well as abrasive particles.

SKF’s oil-selection discussion on printed 120 [2] also requires attention to oil type and to interactions with seals, paint and water, including miscibility. If an oil product or system changes, request review of those actual materials and conditions instead of carrying over the old maintenance interval automatically.

Agree what is inspected, who decides and what record is kept.

  1. Identify the system and lubricant. Record the actual bath or circulation arrangement and exact oil product. Obtain the bearing/system/lubricant suppliers’ applicable instructions.
  2. Provide the operating context. Include temperature with its measurement location, runtime and relevant water or particle exposure. Distinguish design assumptions from observed conditions.
  3. Define the review evidence. For oil-quality assessment, agree the sampling location and conditions, relevant tests and the supplier’s interpretation criteria. Keep reports attached to the system and operating state they represent.
  4. Record the decision. Identify the responsible reviewer, inspection/change decision and follow-up basis, including how changed temperature, oil or contamination conditions will be reassessed.

The exact Luan row/header, exact SKF model entry and oil-selection/change text and actual tables were independently read and visually checked. No calendar interval, inspection frequency, oil-quality threshold or filter capability is approved for Luan here. No oil sample or installed circuit has been tested.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22309W33
108140360045001.382026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22309W33.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22309W33

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22309W33.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22309W33 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22309W33 row ↗

    Source acquired 2026-10-09; exact W33 row/header independently read and visually checked.45/100/36 units unstated;3600/4500 r/min;108/140 kN;1.38 kg. No oil maintenance interval.

  2. SKF · exact 22309 E entry and oil maintenance conditions ↗

    PDF794 / printed792 exact cylindrical22309E. PDF122–123 / printed120–121 oil-selection material/miscibility review and oil-change guidance: conditional oil-bath advice versus circulation oil-quality assessment. Actual rendered pages/tables viewed and text read. No SKF schedule or oil approval assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.