BearingIndex
THE BEARINGINDEX DIRECTORY

22310 — 50 × 110 × 40 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22310

22310 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 50 × 110 × 40 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
50 unit unconfirmed
Outside D
110 unit unconfirmed
Width B
40 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A higher-rated 22310 alternative still needs the actual seat fit reviewed.

When a quotation proposes another internal design, ask whether the existing shaft and housing specification remains suitable. The exact NSK comparison entry has a fit note that a three-dimension match would miss.

Keep the rating and construction attached to the complete maker designation.

The exact Luan 22310 row [1] lists d/D/B entries of 50/110/40 without dimension units, grease/oil speed ratings of 3400/4300 r/min, dynamic/static ratings of 128/170 kN and reference mass 1.9 kg. It gives no shaft/housing tolerance or complete internal construction.

NSK’s exact cylindrical-bore entry, printed C266–C267 [2], is 22310EAE4, marked with an asterisk. Its own table gives 50/110/40 mm dimensions, dynamic/static ratings of 246,000/234,000 N and approximate mass 1.78 kg. The asterisk identifies NSKHPS, with an oil groove and holes supplied as standard.

The two rating sets have different published units and belong to different makers and complete constructions. The NSK entry does not define Luan’s units, load ratings, internal design or interchangeability. Confirm the actual offered Luan drawing before approving a replacement.

The exact NSK table directs the reader to a different recommended-fit basis.

Remark 2 beneath the actual NSK model table [2] states that recommended shaft fits are different for NSKHPS bearings. It defines its load categories as light at ≤ 0.05 Cᵣ, normal from 0.05 to 0.10 Cᵣ and heavy at > 0.10 Cᵣ, referring to its fit guidance on A164.

This page establishes the table’s note and its applicability to the asterisk-marked 22310EAE4; it does not select a tolerance zone from A164. The categories belong to NSK’s stated fit basis and cannot be assigned to Luan merely by using the Luan 128 kN entry.

If an alternative is proposed, request a fit assessment for the exact construction, actual ring/load conditions and machine seats. A larger catalogue rating or a numerical envelope match does not constitute approval to retain the previous shaft or housing fit.

Ask whether the existing seats can be retained, and require the basis.

Buyer inputDecision to request from the supplier/designer
Actual offered constructionApplicable manufacturer fit guidance for the complete bearing designation, with any alternative clearly identified.
Machine duty and ring/load conditionsThe load classification and fit assessment used for the actual operating cases, rather than a generic model-number rule.
Existing seat specification and conditionWhether the drawing and actual seat records satisfy the approved dimensional, form and surface requirements.
Assembly and acceptanceApproved retained or revised seat drawing, mounting instructions and the checks/records needed for acceptance.

Separate the published catalogue values from the machine’s measured condition. Give the reviewer the controlled seat drawing and any available inspection records; identify missing evidence instead of treating a prior successful installation as approval of a new construction.

The exact Luan row/header and NSK 22310EAE4 row, units, asterisk and actual fit footnote were independently read and visually checked. No shaft/housing tolerance, interference, load-category result, fit correction or cross-brand interchange is calculated or approved here. No existing seat has been measured.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22310
128170340043001.92026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22310.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22310

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22310.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22310 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22310 row ↗

    Source acquired 2026-10-09; exact plain22310 row/header independently read and visually checked.50/110/40 units unstated;3400/4300r/min;128/170kN;1.9kg. No fit or full internal design.

  2. NSK · exact 22310EAE4 entry and NSKHPS fit footnote ↗

    PDF134 / printedC266–C267 exact cylindrical22310EAE4;50/110/40mm,246000/234000N,1.78kg. Actual row/header/sketch and asterisk/NSKHPS/fit Remarks1–2 rendered and viewed; fit note refers toA164, no tolerance zone selected here. NSK definitions and fit categories not applied to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.