BearingIndex
THE BEARINGINDEX DIRECTORY

22311 — 55 × 120 × 43 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22311

22311 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 55 × 120 × 43 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
55 unit unconfirmed
Outside D
120 unit unconfirmed
Width B
43 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 22311 installation review needs more than the three principal dimensions.

For a proposed replacement, ask for the limits at both the shaft and housing abutments. The exact NSK comparison supplies minimum and maximum values for each, plus a separate fillet limit; Luan’s published row leaves these interfaces unresolved.

Separate the recorded bearing envelope from the support interfaces.

The exact Luan 22311 row and header [1] list d/D/B as 55/120/43 without dimension units, grease/oil speeds 3000/3800 r/min, dynamic/static ratings 155/198 kN and reference mass 2.4 kg. They do not give abutment diameters, chamfer dimensions or machine fillet limits.

NSK’s exact 22311EAE4 page [2] specifies a cylindrical-bore bearing with 55/120/43 mm dimensions, dynamic/static ratings 292,000/292,000 N and approximate mass 2.3 kg. Its separate interface fields belong to this full NSK designation. They do not establish Luan’s dimension units or approve a Luan installation.

When comparing a proposed bearing against an existing machine, request the offered part’s own support-interface drawing. A numerical match of the three principal entries does not answer where the rings are supported or which corner limits apply.

Read the minimum and maximum together, and preserve the radius labels.

Exact NSK 22311EAE4 fieldPublished valueWhat to request for the offered Luan part
dₐ minimum / maximum65 / 73 mmIts own minimum and maximum shaft abutment diameters; compare both with the actual shaft drawing.
Dₐ minimum / maximum103 / 110 mmIts own minimum and maximum housing abutment diameters; keep the housing interface separate from the shaft interface.
r minimum2 mmBearing chamfer dimension on the offered bearing’s drawing.
rₐ maximum2 mmPermissible shaft or housing fillet radius for the actual installation.

These are the labels and values on the exact NSK page [2]. The two 2 mm entries refer to different things: a minimum bearing chamfer and a maximum machine fillet radius. Do not turn the first into a required 2 mm shaft radius or treat the second as a bearing chamfer specification.

The dₐ and Dₐ fields are abutment diameters, distinct from bearing bore d and outside diameter D. Preserve the minimum/maximum qualifiers when transcribing a drawing review or quote. None of this table’s numerical limits is assigned to Luan.

Record a decision for each actual interface before accepting the replacement.

  1. Obtain the offered bearing’s controlled drawing. Require units, complete construction, principal dimensions and the applicable support/chamfer limits. Identify which fields remain unavailable.
  2. Mark the existing machine interfaces separately. Identify the shaft abutment, housing abutment, corners or reliefs, and any spacers or adjacent parts. Use the actual drawing and available inspection records rather than a nominal seat size alone.
  3. Have the responsible supplier/designer resolve the match. Request a decision for each diameter and corner interface: acceptable as drawn, revision needed, or still unresolved. A proposed spacer or relief needs its own approved geometry.
  4. Carry the decision into acceptance. Keep the approved bearing and machine drawing revisions, required inspection method and actual results together. A catalogue comparison does not constitute a measurement of the existing equipment.

The exact Luan row/header and NSK 22311EAE4 specifications, abutment/fillet table and interface sketch were independently read and visually checked. No Luan shoulder diameter, corner radius, spacer dimension, machining change or installed contact condition is calculated or approved here.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22311
155198300038002.42026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22311.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22311

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22311.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22311 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22311 row and headers ↗

    Acquired 2026-10-09; exact plain22311 row/header read and viewed:55/120/43 dimension units unstated;3000/3800r/min;155/198kN;2.4kg. No support/chamfer/fillet dimensions.

  2. NSK · exact 22311EAE4 abutment and fillet dimensions ↗

    Read and visually checked 2026-10-09. Cylindrical55/120/43mm,292000/292000N,2.3kg; shaft abutment65/73mm min/max; housing103/110mm min/max; bearing chamfer rmin2mm and shaft/housing fillet ramax2mm, actual interface sketch. Values not assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.