BearingIndex
THE BEARINGINDEX DIRECTORY

22311K — 55 × 120 × 43 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22311K

22311K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 55 × 120 × 43 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
55 unit unconfirmed
Outside D
120 unit unconfirmed
Width B
43 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A matching M60×2 thread does not make two withdrawal sleeves equivalent.

If a replacement quote identifies the sleeve mainly by its thread, ask for the complete bearing-and-sleeve combination. NSK’s exact 22311EAKE4 combination and its neighboring 21311EAKE4 combination share several entries but specify different sleeves and axial dimensions.

The published Luan bearing row does not identify a withdrawal sleeve.

The exact Luan 22311K row and header [1] record d/D/B entries 55/120/43 without dimension units, grease/oil speeds 3000/3800 r/min, dynamic/static ratings 155/198 kN and reference mass 2.4 kg. No sleeve designation, thread, mounting dimensions or approved component combination is supplied by that row.

A quote proposing a withdrawal sleeve therefore needs its own complete component identification and approved drawing. The separately published NSK combination below illustrates a concrete specification issue; it does not establish which sleeve, bore construction or thread Luan approves.

The exact NSK rows share M60×2, yet specify different axial geometry.

NSK’s withdrawal-sleeve table, printed C356 [2], lists 22311EAKE4 + AHX2311. The nearby 21311EAKE4 + AHX311 row has the same shaft diameter, nominal bore and thread. Read each row across its own complete designation:

NSK combinationCommon entriesSeparate dimension entries
22311EAKE4 + AHX2311Shaft d₁ = 50 mm; nominal bore d = 55 mm; thread G = M60×2.B₃ = 54 mm; G₁ = 10 mm; B₄ = 57 mm.
21311EAKE4 + AHX311Shaft d₁ = 50 mm; nominal bore d = 55 mm; thread G = M60×2.B₃ = 37 mm; G₁ = 7 mm; B₄ = 40 mm.

The actual table’s sketch distinguishes B₃, G₁ and B₄ and separately labels G as the thread. A matching thread specification does not make the listed axial dimensions or applicable bearing combinations equal. Keep shaft d₁, nominal bore d and thread G as separate fields.

The values above belong to these exact NSK combinations. They are not Luan sleeve dimensions, installed assembly-width approvals, drive-up distances or required tool-clearance values. No AHX311-to-AHX2311 substitution is approved by this comparison.

Ask for the complete assembly and a mounting/removal plan.

When a supplier proposes a sleeve because its thread matches the old part, request the complete offered bearing and sleeve designations, maker drawings and written compatibility basis. Compare all relevant interfaces with the actual machine arrangement, rather than accepting the thread as the entire specification.

  1. Identify the physical components. Record bearing, sleeve, retention/locking parts and any specified mounting or removal tooling separately. A thread entry does not confirm what is included in the supply.
  2. Review the actual assembly drawing. Have the responsible supplier/designer assess shaft and bore interfaces, axial support, thread engagement and the relevant axial dimensions against the controlled component drawings.
  3. Show installation and later removal. Provide nearby shoulders, housing and adjacent parts so the approved procedure and tool access can be checked for this arrangement. Do not derive travel or access requirements from B₃, G₁ or B₄ alone.
  4. Document the decision. Keep the accepted component combination, drawing revisions, mounting/removal instructions and required inspection records with the purchase specification.

The exact Luan row/header and NSK withdrawal-sleeve rows, full designations, units and actual B₃/G₁/B₄/thread sketch were independently read and visually checked. No Luan sleeve suitability, thread engagement, drive-up stroke, torque, final clearance or tool envelope is calculated or approved here.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22311K
155198300038002.42026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22311K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22311K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22311K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22311K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22311K row and headers ↗

    Acquired 2026-10-09; exact22311K row/header individually read and viewed:55/120/43 units unstated;3000/3800r/min;155/198kN;2.4kg. No withdrawal-sleeve specification or approved combination.

  2. NSK · withdrawal-sleeve rows for 22311EAKE4 and 21311EAKE4 ↗

    PDF179 / printedC356–C357 actual rendered spread read/viewed. LeftC356 exact22311EAKE4+AHX2311 and21311EAKE4+AHX311 bothshaft50/bore55mm/threadM60x2; B3/G1/B4 respectively54/10/57 and37/7/40mm. Sketch/headers read. No Luan compatibility, installed dimension or tool-stroke approval.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.