BearingIndex
THE BEARINGINDEX DIRECTORY

22311W33 — 55 × 120 × 43 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22311W33

22311W33 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 55 × 120 × 43 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
55 unit unconfirmed
Outside D
120 unit unconfirmed
Width B
43 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A centralized grease system still needs a point-specific plan for 22311W33.

If the supplier proposes automatic greasing, ask how the actual 22311W33 position receives grease, disposes of used grease and shares a maintenance schedule with the other bearings. The model row does not answer those system questions.

The exact row records the bearing; it does not configure the grease system.

The exact Luan 22311W33 row and header [1] give d/D/B entries 55/120/43 without dimension units, grease/oil speeds 3000/3800 r/min, dynamic/static ratings 155/198 kN and reference mass 2.35 kg. No grease product, feed geometry, supply quantity, cycle, purge path or maintenance interval is specified.

For a separate maker reference, SKF’s exact cylindrical-bore 22311 E row, printed 792 [2], gives 55/120/43 mm, dynamic/static ratings 280/280 kN and mass 2.45 kg. SKF’s own construction and units do not establish those missing Luan system details or approve a cross-brand replacement.

Obtain the actual offered Luan lubrication-feature drawing before deciding where the housing supplies grease. Keep the offered bearing specification and the proposed lubrication-system specification as linked, separately reviewable documents.

Automatic and continuous lubrication are separate procedure choices.

SKF’s relubrication procedures on printed 114 [2] distinguish manual replenishment, automatic centralized relubrication and continuous lubrication. It describes centralized systems as useful for multiple points, difficult access or remote operation, while continuous lubrication is discussed for short estimated intervals under very severe contamination.

For continuous lubrication, SKF derives quantity per unit of time by spreading the replenishment quantity over the relubrication interval. Its discussion has speed, operating-condition and housing-seal qualifications. It does not mean that every automatic system must continuously feed the same amount to every point.

SKF also notes that, when different bearing types are used in one bearing arrangement, common practice is to apply the shortest estimated relubrication interval from those bearings. Before accepting a shared maintenance schedule, ask which bearings and conditions were evaluated and which point governs the proposed interval. No interval is calculated for Luan here.

The same page requires a provision for used grease to leave the housing. It discusses contact-seal type/orientation and an escape hole where needed, warning that tubing on that escape hole can restrict grease escape. This is SKF guidance for a design review; it is not an instruction to drill or alter your housing without the responsible designer’s approval.

Make the system quote reviewable at the actual bearing position.

Record for each pointDecision to request
Bearing and dutyComplete designation, actual load/speed/temperature/contamination cases and approved lubricant; identify the basis used for its maintenance needs.
Supply and deliveryApproved connection to the actual bearing/housing, delivery amount and time basis, and commissioning evidence at the intended point rather than pump operation alone.
Used-grease disposalApproved escape/purge route, seal relationship and access for the actual housing; identify any required design change.
Schedule and responsibilityIndividual interval assessments, basis of any shared schedule, relevant governing point and assigned inspection/maintenance responsibility.

Give the supplier/designer a list of all relevant bearing positions and actual access constraints. Require the returned plan to identify missing evidence, the approved procedure and the checks needed for commissioning. A statement that the machine has a central pump does not by itself document delivery and disposal at the 22311W33 position.

The exact Luan row/header, SKF 22311 E row and actual SKF procedure page, figures and mixed-arrangement interval statement were independently read and visually checked. No grease quantity, interval, pump setting, pipe size, escape-hole dimension or installed delivery result is calculated or approved here. No actual system has been tested.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22311W33
155198300038002.352026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22311W33.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22311W33

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22311W33.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22311W33 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22311W33 row and headers ↗

    Acquired 2026-10-09; exact22311W33 row/header individually read/viewed:55/120/43 units unstated;3000/3800r/min;155/198kN;2.35kg. No grease-system settings or maintenance interval.

  2. SKF · exact 22311 E row and relubrication procedures ↗

    PDF794 / printed792 cylindrical22311E exact55/120/43mm,280/280kN,2.45kg. PDF116 / printed114 actual figures/text rendered and viewed:manual/automatic/continuous distinction, qualified quantity/time basis, used-grease purge and contact seals/escape-hole restriction, shortest estimated interval in mixed-bearing arrangement. No settings or suitability assigned to Luan.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.