BearingIndex
THE BEARINGINDEX DIRECTORY

22312 — 60 × 130 × 46 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22312

22312 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 60 × 130 × 46 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
60 unit unconfirmed
Outside D
130 unit unconfirmed
Width B
46 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A sealed alternative needs both an installation check and a grease-life assessment.

If a quote proposes a sealed bearing to reduce maintenance, first confirm the complete offered designation and available space. The exact SKF comparison changes width from 46 to 53 mm; its grease-life guidance also has operating conditions that a “maintenance-free” label leaves out.

The sealed example has the same bore and outside diameter, but a different width.

The exact Luan 22312 row/header [1] record d/D/B entries 60/130/46 without dimension units, grease/oil speeds 2800/3600 r/min, dynamic/static ratings 168/225 kN and reference mass 3 kg. The row does not specify seals, initial grease or a grease-life assessment.

SKF’s actual product rows, printed 794 [2], distinguish these complete cylindrical-bore parts:

SKF designationPrincipal dimensionsPublished rating details
22312 E60 × 130 × 46 mmDynamic/static 325/335 kN; reference/limiting speeds 4000/5300 r/min; mass 3.1 kg.
BS2-2312-2RS/VT14360 × 130 × 53 mmDynamic/static 325/335 kN; limiting speed 2500 r/min; no reference-speed value shown; mass 3.4 kg.

The sealed example is wider, and its speed fields differ. A shared bore/outside diameter or shared basic load ratings do not close the assembly-space and operating review. These SKF values do not confirm Luan’s units or approve either SKF part as a replacement.

SKF’s grease-life L₁₀ describes lubrication reliability under stated conditions.

On printed 776 [2], SKF defines grease-life L₁₀ as the time at whose end 90% of bearings remain reliably lubricated. It depends on load, operating temperature and speed. This is a lubrication-life definition; it is not a promise that every bearing will run for the machine’s entire required service duration.

For the standard SKF LGEP 2 fill identified by VT143, SKF distinguishes light-load P ≤ 0.067 C and normal-load P ≤ 0.125 C diagrams. The stated conditions include a horizontal shaft, inner-ring rotation, temperature in the grease’s green zone, a stationary machine, low vibration and Fₐ/Fᵣ ≤ e.

SKF also requires rotational speed below both the product limiting speed and the separate grease-life calculation limits on printed 778. For the listed 223-series group, Table 2 gives maximum ndₘ values of 250,000 mm/min at light load and 150,000 mm/min at normal load. Those are speed factors with a diameter term, not rotational speeds in r/min.

No operating load category, grease-life hours or speed-factor result is calculated for Luan or for your machine here. A supplier must identify the applicable design, lubricant, conditions and calculation basis for its actual proposal.

“Sealed” does not remove the need to compare grease life with required service life.

SKF’s next page, printed 777 [2], says sealed bearings may require relubrication when required service life exceeds grease life. Its guidance addresses the lubrication holes, slow application and use of the same grease as the initial fill. The statement qualifies the earlier description of two-sided sealed bearings as virtually maintenance-free.

For a sealed alternative in your 22312 position, request the supplier’s assessment for the required service duration and actual operating cases. If replenishment is needed, obtain the approved procedure and confirm that the actual arrangement provides access. If a different grease or design is offered, its own maker’s approval is needed.

This page does not assign SKF’s refill formula or procedure to an unspecified Luan part. It does not establish that Luan 22312 is sealed or that the proposed housing can accept or relubricate the sealed SKF example.

Ask for two explicit decisions: can it fit, and can its lubrication meet the duty?

  1. Close the physical review. Require the complete offered designation and controlled drawing; compare width, bore form, support interfaces and seals against the actual assembly space and machine drawing.
  2. Close the lubrication-life review. Provide the required duration, actual load and speed cases, temperature, orientation/ring rotation and vibration. Require the supplier’s applicable conditions and result, with missing inputs identified.
  3. Write the maintenance outcome. Record whether the approved proposal meets the duty without replenishment or requires an approved procedure, access and schedule. Keep any assumptions with the assessment.

The exact Luan row/header, SKF open/sealed 22312 rows and actual sealed-bearing grease-life pages, diagrams, conditions and speed-factor table were independently read and visually checked. No installed fit, grease-life hours, refill quantity, operating approval or firsthand reliability result is claimed.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22312
1682252800360032026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22312.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22312

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22312.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22312 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22312 row and headers ↗

    Acquired 2026-10-09; exact22312 row/header read/viewed:60/130/46 units unstated;2800/3600r/min;168/225kN;3kg. Seal and grease-life details absent.

  2. SKF · open/sealed 22312 variants and conditional grease-life guidance ↗

    PDF796 / printed794 exact22312E andBS2-2312-2RS/VT143:width46 vs53mm,325/335kN both; speed/mass fields read. PDF778–780 / printed776–778 actual pages rendered/read/viewed:grease-lifeL10 definition90% reliably lubricated, VT143 load diagrams/operating conditions, relubrication when service exceeds grease life, Table2 speed-factor conditions. No Luan sealed design or calculated duty approval.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.