BearingIndex
THE BEARINGINDEX DIRECTORY

22312K — 60 × 130 × 46 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22312K

22312K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 60 × 130 × 46 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
60 unit unconfirmed
Outside D
130 unit unconfirmed
Width B
46 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A lock-nut angle needs a starting position; it is not a torque specification.

If an installer proposes a catalogue tightening angle for 22312K, ask whose method it is, which seat it applies to and where the final rotation begins. SKF’s published guidance supplies those qualifications; Luan’s bearing row does not.

The Luan row does not publish an angle or a tightening torque.

The exact Luan 22312K row/header [1] list d/D/B entries 60/130/46 without dimension units, grease/oil speeds 2800/3600 r/min, dynamic/static ratings 168/225 kN and reference mass 3 kg. It does not identify the mounting seat, sleeve, nut, taper ratio, angle, torque or clearance acceptance.

For a fully identified comparison, SKF’s tapered-bore 22312 EK row, printed 794 [2], gives 60/130/46 mm and dynamic/static ratings 325/335 kN. SKF’s own designation definition on printed 790 identifies K as a 1:12 tapered bore. Neither that definition nor the SKF mounting values below confirms the offered Luan construction.

SKF’s 115° entry is an angle for a stated method, with stated limits.

SKF Table 7, printed 789 [2], organizes tapered-bore spherical-roller mounting guidance by bearing bore d. The row 50 < d ≤ 65 mm includes a lock-nut tightening angle α of 115° for taper 1:12. The exact 60 mm SKF comparison falls in that bore range.

The angle/axial-drive-up footnote limits the listed guidance to solid steel shafts and general applications. It says the values are guidelines because an exact starting position is difficult to establish, and that drive-up varies slightly between bearing series. It is not an unconditional instruction for every shaft or a prescription for the Luan part.

The α column is measured in degrees. It is not a torque value in N·m, not a rotation to begin from an arbitrary loose-nut position, and not permission to derive a torque from the catalogue angle. Request the exact offered maker’s approved instruction for the actual seat and assembly.

The starting reference and residual-clearance check belong in the instruction.

SKF’s lock-nut-angle discussion on printed 205 [2] applies to bearings with bore d ≤ 120 mm. Before final tightening, it directs the bearing to be firmly positioned on the tapered seat; the recommended angle is then applied. It also says residual clearance should be checked where possible.

Table 7 separately explains that its recommended mounting values do not ensure correct radial internal clearance during operation. Housing fit and temperature differences between the rings must also be considered when choosing the initial clearance class.

For the proposed Luan assembly, have the responsible maker/designer define a reproducible starting reference, the applicable method and the final acceptance checks. A completed nut rotation alone does not document the bearing’s operating-clearance assessment.

Require an installation record another technician can understand.

RecordWhat it should identify
Applicable parts and instructionComplete bearing/seat/sleeve/locking set, material and solid/hollow shaft condition, controlled drawings and approved procedure revision.
Starting reference and methodHow the specified start is established, the approved measurement method/tool and its units; identify angle and torque separately if both are specified.
Final checks and lockingRequired residual-clearance or other acceptance checks, actual readings, final locking condition and unresolved deviations.
Operating-clearance reviewThe responsible assessment of initial clearance, housing fit and operating-temperature effects for the actual bearing arrangement.

The exact Luan row/header, SKF 22312 EK row/K definition, actual Table 7 row and footnotes, and lock-nut-angle explanation/figure were independently read and visually checked. No Luan angle, torque, interference, clearance class or installed result is calculated or approved here.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22312K
1682252800360032026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22312K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22312K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22312K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22312K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22312K row and headers ↗

    Acquired 2026-10-09; exact22312K row/header individually read/viewed:60/130/46 units unstated;2800/3600r/min;168/225kN;3kg. No taper ratio, mounting method/angle/torque or clearance acceptance.

  2. SKF · exact 22312 EK and qualified lock-nut-angle guidance ↗

    PDF796 / printed794 exact22312EK60/130/46mm,325/335kN. PDF792 / printed790 K taper1:12. PDF791 / printed789 Table7 bore>50<=65 alpha115deg taper1:12; actual footnote solidsteel/generalapplications/guidelines and operating-clearance limitation. PDF207 / printed205 angle method d<=120mm, firm starting position, residual-clearance check; actual rendered pages/figures read and viewed. No Luan instruction or torque approved.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.