The source does not state dimension units. Obtain the offered drawing before using these historical values.
Spherical roller
22312W33
22312W33 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 60 × 130 × 46 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.
Check the housing passages as well as the new bearing before assembly.
A new bearing and a W33 designation do not document the cleanliness of the assembled lubrication path. Ask for a preparation procedure covering the delivered bearing, housing passages and any preservative or initial fill.
The row does not state how the bearing is protected or prelubricated.
The exact Luan 22312W33 row/header [1] list d/D/B entries 60/130/46 without dimension units, grease/oil speeds 2800/3600 r/min, dynamic/static ratings 168/225 kN and reference mass 2.95 kg. They do not specify the delivered seal condition, preservative, initial lubricant or preparation procedure.
SKF’s separately identified cylindrical-bore 22312 E row, printed 794 [2], has 60/130/46 mm dimensions. Its E-design description on printed 776 provides an annular outer-ring groove and three lubrication holes as standard. That description is specific to SKF; it does not prove the geometry or supplied condition of the offered Luan 22312W33.
Request the actual bearing drawing and supplied-condition information before opening or cleaning it. If packaging has been damaged or handling exposure is suspected, record that observation and obtain the maker’s preparation/inspection response. No damaged Luan delivery has been observed here.
SKF’s preparation guidance includes lubrication holes and machining recesses.
SKF’s mounting preparation on printed 200 [2] calls for parts, tools, data and the assembly sequence to be ready, with bearings retained in original packaging until immediately before mounting. It describes a dry, dust-free assembly area and protection where the position is exposed to dirt or moisture.
Its component-checking discussion includes the housing, shaft, seals and other parts. It specifically identifies lubrication holes, threaded holes, lead-ins and grooves as places where machining remnants can collect, and addresses remaining casting sand and burrs. After cleaning and drying, dimensional and geometrical checks still remain.
For the proposed 22312W33 installation, give the responsible supplier/designer the actual housing and feed arrangement. Ask which passages, recesses and interfaces require inspection before assembly, what constitutes acceptance and which records are needed. Cleaning a visible outside surface alone does not document preparation of the entire feed path.
A preparation instruction must preserve the seal and initial-fill exceptions.
The same SKF page normally leaves new-bearing preservative in place, with the outside and bore surfaces wiped. It addresses washing/drying when the intended lubricant is incompatible with the preservative. It also separately states that grease-filled bearings capped by seals or shields should not be washed before mounting.
Read those qualifications together with the contamination discussion. Do not turn “suspected contamination needs attention” into an instruction to wash every delivered bearing, and do not treat an unidentified protective film as the intended operating lubricant.
Question before preparation
Response to obtain for the actual Luan supply
What has been delivered?
Complete construction, seal/shield condition, packaging observations and preservative or initial-fill identity.
Is cleaning necessary and compatible?
Maker-approved decision for the exact condition and intended lubricant, with any seal/grease exceptions retained.
Which associated parts require checking?
Actual lubrication passages, recesses, housing/shaft/seal interfaces and the required cleanliness and dimensional inspections.
When can assembly proceed?
Completed preparation/inspection records, unresolved findings closed by the responsible party and the approved assembly instruction.
The exact Luan row/header, SKF 22312 E row/design description and actual preparation page with its cleaning exceptions were independently read and visually checked. No Luan contamination, preservative compatibility, solvent choice, cleaning result, machining change or installed feed-path condition is claimed. No delivery or machine has been inspected firsthand.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.
Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers
168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for 22312W33.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
PDF796 / printed794 exact22312E60/130/46mm; PDF778 / printed776 E standardgroove/3holes. PDF202 / printed200 actual preparation page rendered/read/viewed:packaging/assembly area, associated lubrication/thread holes/recesses and residual machining material, preserve/cleaning qualification and sealed/shielded pregreased non-washing exception. No Luan feature geometry, contamination or cleaning approval inferred.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies