BearingIndex
THE BEARINGINDEX DIRECTORY

22313K — 65 × 140 × 48 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22313K

22313K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 65 × 140 × 48 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
65 unit unconfirmed
Outside D
140 unit unconfirmed
Width B
48 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Keep the exact sleeve type and code; do not reconstruct it from a nearby model.

NSK’s 22313EAKE4 comparison has an X-containing adapter combination but a withdrawal-sleeve combination without that X. The neighboring 22312 withdrawal entry uses AHX2312. Read the actual row for the required component type before preparing a parts list.

The Luan 22313K record does not identify an approved sleeve.

The exact Luan 22313K row/header [1] list d/D/B entries 65/140/48 without dimension units, grease/oil speeds 2400/3200 r/min, dynamic/static ratings 188/252 kN and reference mass 3.6 kg. No adapter, withdrawal sleeve, nut, washer or approved mounting-set designation appears in that row.

If a quotation includes a sleeve, require the offered maker’s actual assembly specification. The following NSK entries are separately identified catalogue combinations, not a prescription of accessories for Luan.

For NSK 22313EAKE4, H2313X and AH2313 belong to different component types.

NSK table and exact combinationPublished interface identificationWhat must stay in the parts list
Adapter table: 22313EAKE4 + H2313XShaft d₁ = 60 mm; nominal bore d = 65 mm. The separate adapter-sleeve column names A2313X.Adapter type, complete combination and separate component-column identity, as published on printed C349.
Withdrawal table: 22313EAKE4 + AH2313Shaft d₁ = 60 mm; nominal bore d = 65 mm; thread G = M75×2.Withdrawal type and exact AH2313 code, as published on printed C356.

The exact NSK tables [2] use different component types and designation columns. Do not substitute the A2313X component-column name for the complete H2313X combination without resolving the actual supply, and do not insert X into AH2313 because the adapter code contains it.

The same withdrawal table lists the neighboring 22312EAKE4 + AHX2312, at shaft d₁ = 55 mm, nominal bore d = 60 mm and thread M65×2. That adjacent X-containing row does not change the published AH2313 code into an inferred AHX2313 entry. It is not evidence that an unlisted variant never exists; it simply cannot approve an invented catalogue transcription.

The adapter-table X remark concerns narrow slits and straight-tab washers. It belongs to that adapter discussion, and cannot be used to define an unspecified withdrawal component or a Luan assembly. Matching shaft/bore entries between the two 22313 tables also does not make the two sleeve types interchangeable.

Request the complete set by component type before accepting the order.

  1. Identify the required arrangement. State whether the actual machine uses an adapter sleeve, withdrawal sleeve or another approved tapered-seat arrangement. Provide the existing drawings and full component identities where available.
  2. Obtain the actual offered maker’s parts list. Keep bearing, sleeve, nut and locking device on separate lines. Require each complete code and drawing revision, and ask which items are included in the quoted supply.
  3. Resolve different or incomplete codes. Request a current maker document and written compatibility decision for any proposed variant. Do not approve a code assembled from a neighboring row, another component type or a matching final number.
  4. Close the assembly review. Have the supplier/designer confirm the actual shaft and axial support/retention interfaces, mounting/removal procedure and acceptance records for the complete offered set.

The exact Luan row/header and NSK adapter/withdrawal rows, separate component columns, shaft/bore/thread headers and actual adapter X remark were independently read and visually checked. No Luan sleeve selection, component inclusion, washer geometry, torque, drive-up value or installed compatibility is calculated or approved here.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22313K
188252240032003.62026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22313K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22313K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22313K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22313K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22313K row and headers ↗

    Acquired 2026-10-09; exact22313K row/header individually read/viewed:65/140/48 units unstated;2400/3200r/min;188/252kN;3.6kg. No approved accessory set.

  2. NSK · exact 22313 adapter and withdrawal combinations ↗

    PDF175 / printedC349 exact22313EAKE4+H2313X, shaft60/bore65mm, separateA2313X column and adapterX remark. PDF179 / printedC356 exact22313EAKE4+AH2313 shaft60/bore65/threadM75x2; neighboring22312EAKE4+AHX2312 shaft55/bore60/threadM65x2. Actual rendered spreads/sketches and headers read/viewed. No unlisted-code existence claim or Luan assembly approval.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.