BearingIndex
THE BEARINGINDEX DIRECTORY

22313W33 — 65 × 140 × 48 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22313W33

22313W33 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 65 × 140 × 48 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
65 unit unconfirmed
Outside D
140 unit unconfirmed
Width B
48 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A filter specification does not replace a measured oil sample.

For an oil-lubricated 22313W33 proposal, ask what filter is specified, where it operates and what an actual sample represents. A particle-size label alone cannot answer whether the oil reaching the bearing meets the agreed requirement.

The factory row does not describe an installed filtration system.

The exact Luan 22313W33 row and headers [1] list d/D/B entries 65/140/48 without dimension units, grease/oil speeds 2400/3200 r/min, dynamic/static ratings 188/252 kN and reference mass 3.55 kg. They do not identify an oil circulation arrangement, filter, sampling point or required cleanliness.

Request the exact supplied bearing drawing and the proposed oil circuit together. The person selecting the system should be able to locate the bearing feed, return, filter and sampling point on that drawing. If a quotation simply adds “filtered oil” to the bearing designation, ask for the missing system specification before treating the proposal as complete.

Separate a design proposal from installed evidence. A circuit drawing can describe intended routing; an inspection record can document the actual installation; a dated oil sample can describe the sampled oil under recorded conditions. Request each record when it is needed for the acceptance decision.

Particle size, filtration efficiency and oil cleanliness answer different questions.

SKF’s technical publication [2] defines β as an upstream/downstream particle-count ratio for a specified size. Its example β6(c)=75 means one in 75 particles of 6 μm or larger passes; a “6 μm” label alone omits efficiency.

ISO 4406 codes describe particle counts. The publication distinguishes automatic counting at ≥4/6/14 μm(c) from microscopy at ≥5/15 μm. Its contamination-factor assessment also depends on bearing size, viscosity conditions and filtration arrangement. These definitions neither establish the actual oil condition nor select a target for this Luan bearing.

Ask the filter supplier to provide its complete declaration and applicable method. Ask the oil laboratory to identify the counting method with the reported code. Give both records to the responsible designer; do not silently compare reports with different methods or turn a filtration declaration into a passed oil test.

Agree what the sample must represent before ordering the test.

Record to requestWhat the buyer needs answered
Oil circuit and filter declarationWhich exact filter is offered, where is it fitted and what complete efficiency/size declaration supports the proposal? Have any bypass or separate filtration paths been identified?
Sampling planWhich point will be sampled, under what operating condition and by whose procedure? Why does that sample address the oil condition relevant to this bearing?
Dated laboratory reportDoes the report identify the sample, location, date, lubricant, counting method and result? Can it be linked to the agreed sampling plan and actual installation?
Acceptance decisionWhat requirement was agreed, who assessed the result and what follow-up is required for an unexplained or unacceptable result? Record the decision separately from the laboratory numbers.

Send an enquiry with the actual bearing designation, circuit sketch, duty and available reports attached. Ask the supplier to return the missing records and explain the proposed acceptance procedure. If no sample has been taken, label oil condition as unverified rather than presenting the filter specification as evidence of measured cleanliness.

The exact Luan row/header and the cited technical definitions were independently read and visually checked. No filter has been selected here, no cleanliness target or bearing life has been calculated, and no Luan installation or oil sample has been inspected. The factory’s unstated dimension unit remains unresolved.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22313W33
188252240032003.552026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22313W33.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22313W33

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22313W33.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22313W33 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22313W33 row and headers ↗

    Acquired 2026-10-09; exact row/header independently read/viewed:65/140/48 units unstated;2400/3200r/min;188/252kN;3.55kg. No installed filtration or oil cleanliness record.

  2. SKF · Method for estimating contamination factor based on lubricant cleanliness ↗

    Pages 1–2 read/rendered/viewed:filter ratio, counting methods and assessment conditions. No Luan target or measured result inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.