BearingIndex
THE BEARINGINDEX DIRECTORY

22314 — 70 × 150 × 51 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22314

22314 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 70 × 150 × 51 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
70 unit unconfirmed
Outside D
150 unit unconfirmed
Width B
51 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Ask what the proposed special execution actually changes.

A supplier may offer an upgrade for vibration, rapid starts or higher speed. Those requests need separate evidence. The exact offered construction and rating fields matter more than a general “special bearing” label.

The Luan row does not identify a vibration or high-speed execution.

The exact Luan 22314 row/header [1] list d/D/B entries 70/150/51 without dimension units, grease/oil speeds 2200/3000 r/min, dynamic/static ratings 230/315 kN and reference mass 4.4 kg. They do not publish a special vibration execution, acceleration allowance or high-speed upgrade for this supply.

Write the reason for the proposed change into the enquiry: a higher operating speed, repeated starts, rapid speed changes, an impact event or another identified duty. Include the actual cycle and available machine records. Calling an application “demanding” leaves the supplier without a clear requirement to assess.

If the supplier proposes a different bearing, keep its complete designation beside the original requirement. Ask which construction, clearance, lubricant or installation requirements change, and where the offered rating is documented. Do not use a special execution from another manufacturer as proof of what Luan will supply.

These two SKF 22314 rows have identical listed speed fields.

SKF’s separately identified product table, printed 794 [2], gives:

SKF designationd/D/B, mmC/C₀, kNReference/limiting speed, r/minMass, kg
22314 E70/150/51413/4303400/45004.55
22314 E/VA40570/150/51413/4303400/45004.55

SKF’s vibratory-design description, printed 778–779, includes hardened steel cages and C4 clearance. Permissible acceleration depends on its mode and lubricant; cited acceleration values apply to oil lubrication.

The identical listed speed fields do not make the two constructions identical. Conversely, a vibration-oriented construction does not establish a higher listed speed in these rows. For an actual offer, request both the exact construction and the rating relevant to the stated problem.

SKF’s reference/limiting columns are not Luan’s grease/oil columns. Their dimensions carry an explicit mm unit, while Luan’s examined header does not. These rows therefore explain a comparison problem; they do not approve a substitution or supply missing Luan specifications.

VA991 is a separate range statement, not an uplift for every special bearing.

The SKF high-speed discussion on printed 780 identifies VA991 special executions in the 223/232/240/241 series with 50% higher limiting speeds than standard bearings. It directs enquiries to SKF. That range statement does not confirm an exact 22314 VA991 offer.

Do not multiply the Luan 22314 speed entries by that percentage. Do not apply it to the examined SKF E/VA405 row. Ask for the exact proposed bearing, its own controlled rating document and current availability; then have the responsible designer assess the proposed operating duty and arrangement.

Claim in a proposed quotationEvidence needed before accepting the change
“Higher-speed special version”Complete offered designation, manufacturer-confirmed availability, its exact rating source and the conditions underlying the proposed operating speed.
“Suitable for vibration”Identified vibration/acceleration duty, lubricant, construction and the maker’s assessment for that actual combination.
“Same dimensions, direct replacement”Controlled drawing with units, arrangement and interface review, clearance/fit and lubrication requirements, and approval of any resulting changes.

The Luan row, exact SKF comparison rows and relevant special-execution descriptions were independently read and visually checked. No actual speed increase, acceleration allowance, Luan special construction, interchangeability, available stock or machine performance has been verified here.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22314
230315220030004.42026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22314.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22314

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22314.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22314 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22314 row and headers ↗

    Acquired 2026-10-09; independently read/viewed:70/150/51 units unstated;2200/3000r/min;230/315kN;4.4kg. No special execution documented.

  2. SKF · exact 22314 E / E/VA405 rows and separate VA991 range ↗

    Printed 794 exact rows;778–780 special executions and conditions read/rendered/viewed. No Luan construction or exact VA991 availability inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.