BearingIndex
THE BEARINGINDEX DIRECTORY

22314K — 70 × 150 × 51 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22314K

22314K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 70 × 150 × 51 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
70 unit unconfirmed
Outside D
150 unit unconfirmed
Width B
51 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A clearance class and a mounting reduction are different records.

Before accepting a tapered-bearing installation proposal, identify the supplied clearance class, measured starting clearance, mounting change and operating assessment. A catalogue range cannot stand in for all four.

The Luan row does not specify a clearance class or measured clearance.

The exact Luan 22314K row/header [1] list d/D/B entries 70/150/51 with dimension units unstated, grease/oil speeds 2200/3000 r/min, dynamic/static ratings 230/315 kN and reference mass 4.4 kg. They do not identify a supplied radial clearance class, measured starting clearance or installation acceptance criterion.

Ask for the complete offered designation and controlled drawing first. If the quotation adds a clearance suffix or describes a “larger clearance” version, require the maker’s definition and evidence for that actual supply. Do not select a class from the recorded speed, load rating or K character alone.

Keep the ordered class, the supplier’s stated range and a measurement of an identified physical bearing in separate fields. A catalogue class range describes a specification; a recorded measurement needs a bearing identity, state, method and date.

The SKF example is 70 mm, above the 65 mm table boundary.

SKF’s exact 22314 EK row, printed 794 [2], gives 70/150/51 mm; its K definition is a 1:12 tapered bore. Table 5 on printed 783 gives these ranges for d >65 and ≤80 mm:

SKF tapered-bore clearance classRadial clearance range, micrometres
Normal70–95
C395–120
C4120–150

SKF specifies unmounted bearings under zero measuring load for these clearance values, printed 781.

The “>” and “≤” headings decide the row: an exact 65 mm bore belongs to the preceding range, while this SKF 70 mm example does not. Preserve the μm heading with the numbers. Luan’s unconfirmed dimension unit cannot be filled from this SKF example, nor can these class ranges be assigned to the Luan supply.

A reduction range describes a change, not the supplied class or final operating state.

SKF Table 7, printed 789, lists a 0.035–0.040 mm radial clearance reduction for d >65 and ≤80 mm. Its guidelines are qualified for solid steel shafts/general applications. It explicitly requires housing fit and ring temperature effects to be considered for operating clearance.

The same reduction expressed in micrometres is 35–40 μm. That is a unit conversion of a change; it does not turn the reduction into an initial clearance range or a required final clearance. Do not subtract catalogue endpoints to manufacture a guaranteed operating result for an unmeasured bearing.

For the proposed Luan installation, ask the maker to identify the approved mounting criterion and measurement procedure for the actual bearing and support arrangement. Record what was measured before mounting, what changed and the final mounted reading where required. Keep any operating assessment with its fit and temperature assumptions attached.

Make every clearance number traceable to a state and decision.

StageRecord to obtain for the actual offer
Ordered and deliveredComplete designation, maker-defined class/range and the document or marking identifying the supplied bearing.
Before mountingActual bearing identity, measurement state and method, result with units, date and unresolved measurement limitations.
Mounting completionApproved procedure and criterion, documented mounting change and final measurement where required, and the responsible acceptance decision.
Operating reviewActual arrangement, fit and temperature/load assumptions, the responsible designer’s assessment and any follow-up verification required.

The exact Luan row/header, SKF 22314 EK row, table boundaries, units and qualifications were independently read and visually checked. No Luan clearance class, taper, mounting reduction, residual clearance or operating result has been selected or measured here. No physical bearing or installation has been inspected.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22314K
230315220030004.42026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22314K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22314K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22314K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22314K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22314K row and headers ↗

    Acquired 2026-10-09; exact row/header independently read/viewed:70/150/51 units unstated;2200/3000r/min;230/315kN;4.4kg. Class and mounting criteria unspecified.

  2. SKF · 22314 EK and clearance states ↗

    Printed 794 exact row;790 K;781 measurement state;783 Table5 and789 Table7 independently read/viewed. No Luan class or installation approval inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.