BearingIndex
THE BEARINGINDEX DIRECTORY

22314W33 — 70 × 150 × 51 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22314W33

22314W33 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 70 × 150 × 51 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
70 unit unconfirmed
Outside D
150 unit unconfirmed
Width B
51 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Show where the supplied oil leaves the bearing housing.

An oil pump or feed connection describes only part of a lubrication proposal. For 22314W33, request the return path and intended housing oil condition alongside the supply arrangement before accepting a change.

The factory row has an oil speed entry, not a completed oil-system design.

The exact Luan 22314W33 row/header [1] list d/D/B entries 70/150/51 without dimension units, grease/oil speeds 2200/3000 r/min, dynamic/static ratings 230/315 kN and reference mass 4.4 kg. They do not specify an oil bath, circulating pump, jet, return route or intended housing oil level.

Ask the supplier to name the proposed lubrication method and show it on the actual housing and circuit drawings. Identify whether the proposal retains a bath or intends oil to pass through and drain. If the method changes, ask which existing housing, sealing or return-path assumptions must be reviewed.

Keep the machine’s actual orientation and operating cycle in that enquiry. A bearing designation and oil speed entry are insufficient to locate the supply and return connections, document heat removal or approve an installation.

SKF’s circulation guidance makes drainage part of the lubrication method.

SKF’s oil-method overview, printed 122–123 [2], distinguishes an oil bath from externally pumped circulation without a bath. Circulation can remove heat and carry contaminants to filters or separators; its drainage must prevent oil-level build-up.

The same overview warns that excessive oil-bath levels cause churning and increased temperature. Its oil-jet discussion also requires drainage to avoid churning. These are method-specific design considerations, not a prescribed level or flow for Luan 22314W33.

If an offer promises cooling by increasing oil supply, ask how that oil returns and what operating evidence will support the claim. Obtain a drawing of the complete path, an identified design basis and a verification procedure. A pump’s presence or nominal output cannot by itself document the condition inside the housing.

If the existing machine has an unexplained temperature rise, send the responsible designer the actual observations and operating state. This page has not diagnosed a blockage, overfill, lubricant problem or damaged bearing; it gives the buyer the questions needed to investigate a proposal without inventing a cause.

Request records that connect the drawing to the actual operating condition.

Proposal elementBuyer’s question for the responsible supplier/designer
Named lubrication methodDoes the proposal retain an oil bath, use external circulation without a bath or specify another method? Where is that decision recorded?
Supply and return drawingWhere does oil enter and leave the actual housing, and what components or passages are part of each route? Has the installed orientation been included?
Intended housing oil conditionWhat condition is intended during operation and at rest? Which maker-approved procedure will check it, and what would require review?
Operating verificationWhich supply/return and temperature observations will be recorded for the stated duty? Who assesses them against the approved design and decides whether the proposal can be accepted?

Attach the existing drawing, proposed change and available operating records to the enquiry. Ask for a written response identifying unresolved assumptions and the acceptance procedure. Do not convert a catalogue illustration into a drilling plan, a pump setting or a promised temperature reduction.

The cited SKF figure set contains different bearing and housing examples; it is not a drawing of the Luan 22314W33 installation. In particular, the vertical pumping example is identified in the source text as a spherical thrust roller arrangement, so it does not establish self-pumping by this spherical roller bearing.

The exact Luan row/header and SKF oil-method text/figures were independently read and visually checked. No Luan return passage, oil level, pump output, flow requirement, nozzle, heat balance or operating result has been measured, selected or approved here. No machine has been inspected firsthand.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22314W33
230315220030004.42026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22314W33.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22314W33

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22314W33.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22314W33 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22314W33 row and headers ↗

    Acquired 2026-10-09; exact row/header independently read/viewed:70/150/51 units unstated;2200/3000r/min;230/315kN;4.4kg. Oil method and drainage unspecified.

  2. SKF · oil methods and drainage considerations ↗

    Printed 122–123 text/figures independently read/rendered/viewed:oil bath and pumped circulation/drainage; illustrations retain their actual bearing types. No Luan system design inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.